Polymer Clay Storage: I keep my polymer clay in half-pint canning jars. I use my husband's fancy jars which he would like to keep for his jam. This way, the clay is safe, colors - commercial and my own mixes - are readily identifiable and it looks quite pretty lined up on narrow shelves. I keep my 'leftovers' and larger blocks in bigger jars. E. Westcott |
Plates: Recently there have been several people asking about plates, so I thought I would contribute. I make plates and bowls from a two part clay that we can get in South Africa. It is similar to Prattley's putty that is used for fixing car parts. However, in England, I think Milliput would be the closest. Otherwise, air drying clay such as Das, which is available in white, would do the trick and maybe now Paper Clay. These instructions are for the two-part clay. I take a pea-sized piece of each clay and mix the two together thoroughly. I then roll it between 2 pieces of wax wrap, on a tile, using a glass as a rolling pin. This gets the clay smooth and thin. I take my mold, which is usually a lid of some sorts, and put a THIN layer of Vaseline as a release agent. I lay my clay over it and use my craft knife to cut off the excess. I smooth edges with a "wet" finger. (Sorry, nothing else works!) I leave these to dry overnight and then pop them off their molds. I wash them with HOT soapy water to remove any Vaseline residue. A light sanding smoothes off any rough edges and imperfections. I make colour photocopies of plates reduced to the right size. They must be full face on, bright and clear. Of course, if you want a dinner service, and not just plates to hang on the wall, then you must make bowl-size copies and side-plate-sized copies, as well. I paint these with decoupage transfer medium, leave to dry and then cut them out VERY accurately. I then soak them overnight or longer (they take no harm left for weeks). Meanwhile, I paint the back of the plates with decoupage deco varnish to give the back a finished look. I rub the paper off the back of the photocopied plates, leaving a thin transfer. I slide this onto the wet plates with deco varnish, position it, smooth out any bubbles with a wet brush and then leave them to dry. Three coats of deco varnish, with drying time between, finish them off with a shiny finish. They are very addictive and you end up making far more than you need, even given the fact that my dolls house inhabitant collects antique plates! Barbara Brear in South Africa |
Storage of Fimo and Sculpey III: I wrap individual opened colors in saran wrap/plastic wrap, then in smaller Ziplock bags and then into 2 pound coffee tins w/plastic lids, lined with a plastic bag and twist tied shut. I have my two clays stored in several separate marked tins, until I blend them. One each for flesh colors and for other assorted colors. My assorted color Cernit I wrap in saran wrap then larger Ziplock bags, in hard plastic container. All of my clays have kept for years this way. I covered the tins with wood-look contact paper so it looks good and works well. Regina in Delaware |
Baking clay: How do you know if the items you make from modeling compounds are baked enough? Good question, because all ovens whether regular or toaster ovens, bake differently. I presume that you know to bake clay items at anywhere from 250 degrees to 350 degrees F. To test YOUR oven for the correct temperature, do this: Take a kneaded piece of scrap modeling compound, perhaps 1/2" by 1/2". Shape it irregularly and bake at 275 degrees for ten minutes. Remember that modeling compounds, when taken from the oven, are still soft and harden as they cool. When the piece is cool, slice with an X-acto knife. If it crumbles or even just has a whitish cast to the cut side, you must adjust the temperature of your oven to a higher setting. Another way to test is this: When piece is cool, paint it with a clear gloss and let dry. If the gloss stays tacky, your piece was not baked Hot enough and LONG enough. I will be adding this information to the ALL ABOUT MODELING COMPOUNDS pages, at WORKSHOP at my website. http://www.pannikins.com/ Mary Eccher |
Food processors - I use a small inexpensive food processor. It is a Betty Crocker Mini Chopper and if I remember right was about $15. He is right, tho, NEVER USE FOR FOOD AGAIN. I use the food processor to start blending colors and then transfer to the pasta machine. The processor will warm the Fimo which helps the softening process. I always shave small pieces into the processor before I start it. Don't make it work TOO hard with great big chunks. That would probably burn it out quickly. I have been using this one for about 8 or 10 years and still have no problems. I do use Fimo softener and then add the older colors to it. If you try to just use older drier Fimo by itself you will have zillions of little crumbs and it won't hold together. Remember to do small amounts at a time and as each batch is taken out - stick in a plastic bag and sit on it until you have it all blended. This will keep it warm and ready for the Pasta Machine. Jane King in Indy |
Polymer Clay Conditioning and Storing - When you buy a packet of any polymer clay it is advisable to "condition" your whole block. In other words soften the whole thing. As miniaturists, we tend to break off the little piece we need and leave the it in the open packet. After conditioning, I put the clay in Ziplock baggies and then store in a plastic container with a lid. Store it in a cool place. The fridge is best if you have a space in there you can use. Avoid leaving it in a car on a hot day as it will bake in the heat. As far as I am aware each brand has a shelf life of at least 7 years if stored correctly and even then if you have some old and what seems impossible to restore, clay you can use either Fimo brand Mix Quik or Sculpy Dilutent to revive your clay. Petra |
Pasta Machines - I was able to find a pasta machine at a yard sale, but it's a good investment even at full price. To preserve Fimo, I run it through the pasta machine 2-3 times, making it thinner each go-around. On the last run, I put the Fimo between two sheets of waxed paper and put the "sandwich" through the pasta machine. The pressure adheres the waxed paper to the Fimo in a sort of bond. Then I place the "sandwich" in a Zip-lock bag and store all my "sandwiches" in a Rubbermaid lidded box. Even if any of them should dry out, they will be easy to rework because they are in such thin layers. Anita Myers in Arnold, MD |
Fimo/Polymer Clay Leftovers - A handy little "system" I've found that works fine for me is to keep any leftover clay in the sealable/stackable Tupperware Hamburger savers. I'm not affiliated with them, so I get all of mine at the Goodwill store for CHEAP - ($1-$2 for a bag of a bunch). This "system" is also GREAT for securely storing all types of mini things, and you can stack them 20-30+ high, and then "pop" the section you want. For the clay storage, you could also add the benefit of a baggie, but I've never found it necessary. Many people recommend keeping the clay leftovers in the fridge, your choice. With the large amounts of Fimo/Poly clay I use, I first blend everything in a food processor (before it hits the pasta press,)so this eliminates most problems that occur with normal "handling". Linc Leedy |
Softening Fimo: Go to www.sunshinecrafts.com (Sunshine Discount Crafts website). They have Sculpey Softener, #SD1 (Diluent). Since Sculpey and FIMO are both polymer clays, this should work just as well to soften hardened FIMO. Mary |
Softening Fimo: There's a Fimo product called Mix-Quick, a transparent kneading medium for softening fossilized Fimo. It does lighten the colors somewhat, but not terribly. Also, try mixing your Fimo with the same color of Fimo Soft, which is available in a wide range of colors. Finally, if you're not using a pasta maker to roll the Fimo out, start haunting yard sales or buy a cheapo model (Dee's carries a very good one). I don't know how I lived without mine--you'll have soft, blended Fimo in a matter of minutes. Kate |
| Previous 10 | Next 10 Page 938 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |