From Mary Eccher (author of the Mary's Menus articles for Nutshell News): I will be posting CLASSES on Miniature Cookery using Modelling Compounds and Resin at my website. I will start at the beginning of my articles (Nutshell News 1984) - basic instructions, then give you all my (revised) article instructions, and go on from there. QUESTIONS ON THE USE OF MODELLING COMPOUNDS AND RESINS ARE WELCOME! JUST ASK! Either at my Website or on Small Stuff. Mary Eccher |
Polymer Clay Bath Fixtures: Head off to the library and ask them for Sue Heaser's book Making Doll's House Miniatures with Polymer Clay. She shows how to make a complete bathroom set and includes directions for making tiles as well. If the style of the various pieces doesn't appeal or suit what you need, you can use her basic instructions but adapt them to what you see in a Sears or other catalog. I think this is a wonderful book. And Tom carries it at Earth and Tree, got there first, Tom! Also she provides lots of info on working with clay which would also be a help to you. If your local library doesn't have it you can ask them to get it on an interlibrary loan. Esther in BC |
Cutting FIMO Canes: You can reheat the canes before you cut them. Just use a slightly cooler oven than you baked them at, to keep from scorching them. If you need to cut your canes before baking, make sure you roll them and cut from a different side each time. This helps keep their shape. Another thing is to refrigerate them for a little while to make them firmer. Also, make sure you are cutting them, whether unbaked or baked, with a sharp razor blade or tissue blade. This is not the time to be using an old dull blade. Marsha Heeter |
There are a couple of other ways I know of to slice canes: 1. Is put the cane in the freezer on a ceramic tile and freeze for several hours. Take out and slice on tile with a very sharp and thin razor blade. I use the old fashioned double sided razor blades (be very careful with these blades and cover one of the sharp edges with tape). Then bake in oven on the tile. 2. Put the cane on tile, bake in the oven one or two minutes. The idea is to make the cane slightly firm, not baked until done. Take out and slice when you remember. Put back in oven and bake till done. If you are using Sculpey or a similar brand try using only Fimo. Fimo is much firmer and holds its shape better when sliced. Also always remember to use a sharp and new blade when slicing. Robin in Israel |
Cutting Fimo Canes: Well, I've never tried to do it after baking, I am so afraid to lose a lovely cane by having not enough time to cut it when it is still warm. So, I always cut them when they are 'raw'. When you start cutting a cane it has to be not too soft and not too hard. Medium is the best option. When you try to cut a very soft (warm) cane, the pattern will distort and doing it with a hard (cold) cane, you get little tears. And then the big tears start to run :o( Next is the shape of the cane. Is it round-shaped or square? With a round-shaped one you have to turn it after every cut. Use a very thin and very sharp knife, like the one-edged razorblade. With a square-shaped cane you can take two pieces of wood, put the cane between them and start cutting (let some fimo peep out of the wooden alley of course, for cutting fimo AND wood is a very tough job) you can use a ruler to make equal sizes. Turn regularly.. Marjon de Haas (The Netherlands) |
Colouring fimo: Mixing colours with fimo works like mixing paint: start with the light colours and add (carefully: small amounts) darker colours. Go to the library and get yourself a book on the wheel of colour by Johannes Itten (he is very good, but other authors are fine too). You can start making your desired colour with paint first (write down what you did) and then try it with fimo. Marjon de Haas (The Netherlands) |
There are a couple tips regarding Fimo that I haven't seen, I would like to share. First, to soften Fimo, take a heating pad, set it on the low setting, place a piece of aluminum foil on it, and lay the cut pieces of Fimo there to warm. Second, if you don't have a pasta machine, take your Fimo softened pieces and lay them between waxed paper, then you can roll them with a rolling pin (anyone still own one?? LOL), keep rolling till the pieces are thin, the rolling will also soften the Fimo if you haven't used the heating pad. Another way Fimo can be softened is by using the rice bags made from socks. These warming methods can be used to warm the canes before slicing as well, just don't slice while the cane is on the heating pad. Melissa Dempsey |
toaster ovens for baking modeling compounds. It is truly the way to go, but you may have to raise the temperature setting a bit from the normal instructions. I bake my foods at 300 degrees for ten minutes on mine, but your oven may run temperatures differently. Here is how to test your own ovens, takes a little time, but all future projects will be baked correctly: Bake a small piece of fimo, sculpey, etc. in the oven at the prescribed 250 degrees for 10 minutes. When cool, if it breaks easily, or crumbles, of course it is not baked hot enough, so raise the temp and bake a little longer. Also (when cool), try this test: Paint with clear gloss. When gloss is dry, if the gloss on the piece stays sticky, it should have been baked at a higher temp and a little longer. With a little experimentation, you will determine the correct temp for your oven and all your projects will work out well. Mary EccherMary Eccher |
If you find fimo too hard to knead, there is a product called Mix Quick. Mix one part Mix Quick to one part color and you will have a very workable compound. And by the way, it STAYS that way, never to knead it (or only a little) again. Mix Quick should be available at your craft or miniature shop or CAN be ordered on-line at my website. Just as an aside here....actually FIRM modeling compound is what you WANT, to attain an accurate miniature. Otherwise, things SMUSCH as you try to create them. Mary Eccher |
Cooking Fimo: Set your sculpted piece/s into a small pot or a lg tin can (without label on it), and fill with water. If you use a pot, don't use it for anything else, just curing. I know someone out there will have time tables for how long to simmer/boil your pieces, but I just let them simmer for an hour and let the water cool back down before removing the pieces. Last night I made pie shells from Cernit, which is very like Fimo. I dropped them in boiling water for 5 mins. and they were hard when I took them out and drained them on a paper towel. Filled them with beads for cherry pies today and they seem to be fine. Boiling Polymer Clay: I just place the piece in a "retired" soup pan, make sure it's submerged, and boil it for the same time as baking - 15 mins, generally. Water boils around 225 degrees, which is the recommended temp for Sculpey hardening. Courdee |
| Previous 10 | Next 10 Page 940 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |