Cutting Plexiglass: I personally feel sawing is not a good option, unless trying to cut curved line. I also feel cutting it on a table saw is too dangerous for the amateur. It has a nasty habit of kickback, and I have some holes in the wall to prove it. Main problem is that the heat of the blade, either table or jig, melts the plastic. Best solution is to get a knife especially for scoring Plexiglass from a hardware store. It has sort of a hook-shaped blade, so as you draw in towards you, it will score the Plexiglass. Depending on your strength, thickness, etc., it may take as few as 2 or 3 passes, or maybe up to 10 or more to get a good score. Then place the score line on edge of SHARP edged table and snap the Plexiglass. Until you get the hang of it, you will probably ruin a few pieces. I use a steel ruler as a guide and clamp it to the Plexiglass so the knife doesn't wander off the first score. Most glass stores will cut it for you, but check around, as there are wide variations in what they charge. In my small town glass shop, the cost for the Plexiglass and their cuts were dirt cheap, cheaper than just buying Plexiglass at home supply stores. Instead of Plexiglass, you might also consider polycarbonate - Lexon is one brand name. It is less likely to scratch and a little stronger, although for the front of a room box, extra strength isn't a factor. Dean Jenson |
Cutting Plexiglass: #1 - Score both sides with a utility (Stanley) knife or a plastic cutter which looks like a metal hook with a sharp point. Place the cut over the sharp edge of a table, press down on the free side and it will "pop" apart. #2 - I like this method best. Place masking tape on both sides where the cut will be. Very importantly, it eliminates chipping. I have a 4" table saw with a carbide blade. It just cuts like butter and the blade cools as it rotates. A jig saw doesn't work as the blade has no way of cooling and the heat will melt the plastic. DON'T use a glass cutter, it will ruin it. Ruth Mazur, Grass Valley, CA |
Glue: Periodically, the subject of glue comes up. My husband is a woodworker, and has found a new, fabulous glue!! I used it when I was making my mini scenes in 16" wreaths for Xmas. It is called PROBOND-made by Elmer's. It is a polyurethane glue, waterproof, bonds anything to anything, is paintable/stainable, etc. Takes 24 hrs to cure. During the curing process, it expands to fill gaps & further penetrate porous surfaces. Once glued-always glued!! It's great when you need extra strength. For porous surfaces, you wipe both surfaces with a damp cloth about 1 minute before you clamp the pieces together. For nonporous, you apply glue to 1 side and damp wipe the other surface. The water helps to make the bond. To make my wreaths, I used it for the 1/2" foam core and it worked great. Ninalu in CA |
Tools: Ron Stetkowitz makes and sells a pair of needle nose pliers that has a "T" groove in the tip to hold the small nails for hinges. You hold the nail in the tip of the pliers and push it into the hole in the hinge. After the nail is started, release the pliers and use the blunt tip to seat the nail. I always dip the tip of the nail in a bit of carpenter's glue before inserting in the hole. It dries clear and holds better. I don't have the address for Ron, but I'm betting someone out there does. Spencer Stall |
Tools: I use the pliers and they are great. His address is: Ron Stetkewicz 518-622-8311 Rosemarie Torre |
Removing odors from your work: I use the dryer product called "Bounce" in my tool boxes and it keeps a fresh smell instead of that dank humid Florida aroma. I imagine it would be less daunting then spraying a product onto surfaces. I just take a sheet of bounce and toss it into the tool box. To reduce moisture and odor, try a charcoal briquette. I break a few briquettes and toss them into the tool boxes also. Tools can handle the loose charcoal. For the mini's, the broken briquette can be placed in a "sack" of old panty hose to keep the charcoal from getting onto things. Dr. Bob |
Decoupage liquid: I use the decoupage liquid as a glue and over the top of the fabric or paper as a sealer. The surface I am "gluing" to will have a coat of paint or primer on it so the decoupage liquid doesn't soak in & disappear. This liquid comes in Gloss or Matte,so you can get shiny or dull finishes on paper. It doesn't matter on fabric, as far as my experience goes. Ann in AZ |
Cutting Tubing:The best way to cut brass tubing is by using an X-Acto miter saw and miter box. Use the fine tooth blade. I have been using my original one I got back in high school in 1948. It still cuts the brass just fine. That is the way I have my students cut the tubing in my Guild School Class for my projects. Hold the tube tightly against the back fence and start the cut by dragging the blade backwards on the first cut then saw as normal. Do not force the saw. Let it cut at its own speed. Bill Hudson, Eugene, OR |
Gluing Agate: Dean Jensen (RainbowDJ@AOL.com) has a glue called Roo that he swears by. There is one formulation for wood and another for glass and metal. Someone else is actually selling the stuff and if you contact Dean, he will tell you. He's a nice, talented guy and he just loves the stuff, so it must work. Jeanne |
Gluing Agate: Try using a glue called Weldbond. If your local miniature shop doesn't have it, Home Depot does. At Home Depot it comes in a 16 oz. bottle, I think. Its a white tacky glue but it sticks anything to anything without marring the surface. Mary Kay |
| Previous 10 | Next 10 Page 953 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |