Glue for Perfume Bottles: The best glue to use for gluing your perfume bottles to the trays is Aleene's Thick Designer Tacky Glue. Sticks tight, dries clear.

Mary Eccher


Glue for Perfume Bottles: If 'snow' that seems to form on your superglued perfume bottles. I suspect you are using too much glue. I just use a toothpick and dab the tiniest speck of glue and it holds well with no snow.

Barbara Knox


Glue for Perfume Bottles: How about using a tiny amount of colorless nail polish to glue those beads.

DrBob...Delray Beach, FL.


Crazy glue: Couldn't help but put my two cents in on this glue stuff. If you use glue often enough, you can buy a Debonder put out by Zap-A-Gap that works really well in getting the glue off completely without really tearing your skin. When I get just a little extra glue on my fingers, I rub Avon Cuticle remover on the spot and don't know how or why it works, but the glue eventually comes off without hurting the skin. and doesn't produce any fumes. Nail polish remover works., but is pretty harsh, and as with all chemicals, should be used in well ventilated area. And don't forge to wash the polish remover off your skin afterwards too.

Leilani and Roger Warling


Grip Glue: l met this lovely lady who made and dressed dolls at the last show l was at .And she told me she loved working with it for material and for wigging dolls....She said it didn’t bleed through even on silk materials.

Cindy from Mi


Grip Glue: Unless there is another one I don't know about, you are probably referring to Instant Grrrip which is made by Bond. I use it extensively on just about everything. Only drawback is that is hard to find....it is usually not in your regular craft store.

Dawnsminis


Grip Glue: I love Grip glue. Got mine from Hobby Builders Supply, mail order.

Marjorie in CA


Flexible Shaft: a flexible shaft performs best if used from an overhead position . Either place your Dremel on a shelf over the workbench or hang the Dremel high enough over the workbench to keep from kinking the shaft.

Carol Wagner


Mitering plywood:

A good tool for miniaturists who are building doll houses should be a skill saw of some sort. Although Skill is a brand name it has become the accepted name of all such saws, just like Crescent wrench for adjustable wrenches. The purest may say "hand held circular saw," That is ok but Skill saw works for me (and most others). These can be found at many hardware stores or home improvement stores.

If you are only cutting plywood I would recommend the smaller ones with maybe a four inch blade. They come in several brand names. Many are rechargeable which is nice as you do not have to mess with a cord. An extra battery is nice if you are doing a lot of cutting.

Be sure to get one with a tilting table and make sure when it is set at 45 degrees for a miter cut there is enough blade beyond the table to cut through at least a 3/4' thick sheet.

These little saws work great for cutting plywood sheet down to size and also for mitering. They usually require a guide, (good straight piece of wood) clamped to the wood being cut, to run the table edge against while cutting. Since the blade cuts upwards always cut with the poor side of the wood up. Also get a panel cutting blade (fine teeth) for finer cut. To prevent (decrease) splintering of the wood by the blade put masking tape over the cut line or score it first with a knife blade.

Bill Hudson


Cutting metal tins: My wife asked me to reply to someone who would like to know how to cut an opening in a tea tin to be used as a small room box.

The biggest concern is safety, since you will be working with an abrasive cutoff wheel and will encounter flying grit. I ALWAYS wear safety glasses or a face shield and a dust mask. First apply masking tape to the approximate outline of the hole. Then mark the exact hole to be cut out with a felt tip pen. If the tin has a border or some art work that is to remain showing at the edge of the hole, then skip the tape and marking pen and follow this border. I use a Dremel tool with fiberglass reinforced cutoff wheels. These are about 1-3/8 inch diameter and 1/32 thick. I've found the non-reinforced wheels to be very fragile and break a lot. Speed should be about mid-range on the Dremel for thesewheels.

To do the actual cutting, I sit down, both feet on the floor, and cover my lap with a large towel or pillow case to control the flying grit. Then, holding the tin in my left hand and the tool in my right hand I rest both wrists on my legs. The idea here is to have a very firm base for both tool and tin because the wheel can grab easily, causing damage to the tin or to you. I rotate the tin clockwise about 45 degrees so I'll be cutting at a comfortable angle.

Starting on the right hand side of the hole and about 1/4 inch from the top of the hole, I gently ease the wheel into the tin until the wheel is about 1/8 inch through. Then carefully move the tool along the line until about 1/4 inch from the corner. The plan is to cut all four sides first, then go back and cut the corners last. This way, you won't have to deal with the center cut-out flopping around while trying to finish your cutting. For tins that have a border around the hole, it is safer to rough cut about 1/32 or more from the border, then go back and finish cut to the line. Remember that the tool will skid along the surface sideways marring the surface without warning, so really pay attention when starting the cuts. Once the hole is cut out, use a six inch flat file to smooth the edges and gently file away burrs on the inside and outside.

I have used this procedure to cut holes in tea tins, aluminum coffee pots, large steel enameled coffee pots, and copper tea pots. The main thing to remember is to go slowly and very carefully to avoid mishaps. Good luck!

Jim Nielsen - Wisconsin


Previous 10 | Next 10


Page 960 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)