Square Corners and Straight Walls: My favorite tool for helping the glue hand is: A book rack. The sliding kind that has one sliding end that pushes up to keep the books upright. Mine is made on dowels, one end secure, the other slides. I put my base down and fit one end against the solid end. Move it out slightly and add glue. Add the other end, doing the same thing. When you're ready to leave it to dry, wedge a ruler or stick (pre measured and cut) lightly against the inside of the walls to hold them upright. Bingo! Straight Walls, Secure glued joints. If you're worried about gluing the project to the rack, put down plastic wrap or spray the rack with WD-40. Judie |
Dremel Repair: I have found Dremel does not repair tools that have been discontinued. Instead they will offer a new tool at a reduced price, but may be at a higher price than a discount store. I have located a company that may be able to repair older Dremel tools. I understand it is not associated with Dremel Corp, but run by a relative of the man who invented the MotoTool. Dremel Repairs, 4631 East Sunny Dunes, Palm Springs, CA 92264 -- 619-327-3003 Dean Jenson |
Tools for dollhouse carpentry: X-Acto knife, X-Acto saw and miter box.,masking tape, Ailene's tacky glue, Quickgrab glue, rubber bands several sizes. Then you can use these tools too, though more cost: Dremel scroll saw, Dremel cordless tool and bits, pin vise, and drill bits in miniature, woodworking clamps small. Second hand Rhoda |
Rainbow Design Items: Yes, due to health, I can no longer make miniatures. Fortunately, I have been able to find people to continue making most of the things I made. Also Roo Glue, thin glass and Anker items will continue to be available. I hope all of you will continue to give these people the wonderful support you have given me since I started Rainbow Design in 1984. RAINBOW DESIGN ITEMS (1 and Quarter Inch scales): Paddy Culhane ROO GLUE retail and wholesale: Sandy’s Lace and Trim ANKER TEMPLATES for Duplicator: Smaller Than Life, Pete Boorum ANKER VIDEO INSTRUCTION TAPES Smaller Than Life, Pete Boorum THIN GLASS George Wrisley Dean Jenson |
Glue Bottles: Are the stainless steel tip glue bottles everyone is talking about the one that is on the bottom of page 58 of the new Micro Mark with the accordion bottle? I mostly use the plastic syringe- I use a rubber (plastic) end that you put on the end of your knitting needles to keep your work from coming off on the end, it keeps the glue from drying out and is easy to put on and off. Also here in Nevada you can easily get the 1 oz. and 2 oz. thick bottom "shot glasses" that won't tip over to keep my glue bottles and syringes upside down in. Kathleen |
Glue Bottles: About stainless steel ball-headed pins, I have found that the only way to know which are solid stainless and which are plated, is to try them. Some plated will work for a few months and then start rusting. I like to cut my pins short for 'stopping' my glue syringe, and of course if the pins are just plated... well... bad luck. I tried the plastic from a price tag holder, but it was not satisfactory for me. Probably I had one that was too flimsy. I use a monoject syringe for my glue, and have done for years. I used to sell the syringes. They are curved, which is a big bonus as far as I am concerned. Anyway, we bought them from a Dental Supply House and they are normally used for root canals, ugh. So ask you dentist! Joy Parker |
Scissors: I paid a visit to Michael’s the other day and came away with some interesting off-brand scissors similar to the type Fiskar’s, et. al., makes for edging stuff in scrapbooks. What’s important about these is that a) they're only $2 each (instead of 4.99 - 7.50), and b) there are several that have fancy patterns in sizes that can be used nicely in minis. For example, I tried them out to edge stationery and envelopes between 1/4" and 5/8" wide, and at least 3 different styles gave a clean, unusual, fancy edge to them. A 4th style has little 1/8" scallops, kind of like waves in a decoupage picture, and a 5th one has a row of big scallops (about 5/8" each), and --get this-- each scallop has 7 or 8 mini "pinked" points cut out, each of which is smaller than a pinhead. All for $10! Lynn O’Shaughnessy |
Scallop Scissors: A vendor (Hansens, I think) at the Ben Ali show demonstrated using the scallop/fancy edge scissors to cut thin sheets of wood veneer, creating wonderful trims. They also used hole punches, both round and fancy, to add details to theveneer. Lee |
EZ Cutter: I bought the EZ Cutter after looking at the picture that was sent out. I've used it twice and it is much easier to keep track of the angle you are cutting. Those marks help a lot. Also like the fact that they have replacement blades available right up front. It is certainly a lot cheaper than the German import one. I've had that one for many years now. I think this new one will be quite nice for the tool box. I can't always fit my chopper in my there. MaryLou |
Mitre Cutters: I have the German made hand held mitre cutter that Brooke Tucker recommended for one of her workshops that I took. I have never regretted that purchase. I use it for many things and have never had a problem with it crushing or moving the wood. I get crisp, clean cuts out of it. Been a great tool for trims on my wicker and for cutting siding and shingles. Since that time we have discovered that Lee Valley Tools has an excellent hand held mitre cutter for less than a 1/4 of the price of the German one. From what we've compared, there is no difference in quality. They don't have it on their web page but it is in their catalogue. www.leevalley.com And for you Americans - it's Canadian Dollars - bonus! For doing parquet flooring with mitred corners I have another tool recommended by Brooke. Micromark sells two. One is large and one is small. They are for cutting mitred corners. Can't remember exactly what they are called though. They cut with templates and single sided razor blades mounted on a handle. What this tool allows you to do (especially the longer one) is cut out numerous lengths of wood to all the EXACT same length and then cut the mitred corners off them without loosing any of the necessary length . Every single piece is the exact same size and shape. No guessing and that exactness is the key to a floor that looks good. Works great for framing too. Nothing worse than making a frame and one side is just a eensy weensy bit too long or too short compared to the other matching side. Doesn't happen with this tool. There is also a similiar tool, again made in Canada that I find is better made. Don't know that it is any cheaper but I prefer it. It is made by Don Everett of Ontario. Debi |
| Previous 10 | Next 10 Page 961 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |