Removing Glue: To get the glue off that lovely mirror try a product called DeBonder. It is the solvent for Zap-a-Gap glue but will dissolve lots of glues, though some take longer than others. I've used this product to soften wood glue, contact cement, white glue, etc. Sue |
Weldbond is really good stuff. I use it almost exclusively except for another very good white tacky...GRRRIP. Weldbond I use for all of the heavy duty construction and wood gluing and the GRRRIP I like for fabric, paper, fimo. Mary Kay |
I LOVE weldbond! I have been using this glue for 7 yrs. It is thicker than Elmers and thinner than tacky, it dries clear and will glue unlike substances together. You can get it at Home Depot and Ace Hardware, and Michaels. It is used in construction to strengthen concrete. Great for minis!! Sue Thwaite |
Glue Search site: While I was researching metal glues on the net I found "This to That". You tell this search aide what materials you need to glue (fabric to leather, paper to vinyl, metal to metal, etc), and it gives you suggestions, with links to web sites. Mindy in the Wilds of PA |
Sawing Mini Wood: I have used everything from a 4" Dremel or Jarmac table saw to a Sears 12" table saw to cut mini wood sizes safely. I also use the Anker trim saw, but have no use for the Anker cut off saw that I own because a regular table saw works as well. The tricks, with all these saws, are two: 1. Keep the saw blade height as low as possible to still be high enough to cut all the way through the wood. Most table saw accidents are at least partially attributable to a saw blade set too high. 2. Use a slide table on the saw. A slide table is simply a piece of plywood, Masonic or Plexiglas (about 12" x 12" for a 4" saw) with a runner or runners on the bottom so that it slides across the table in those grooves table saws have. With a 1/2" x 1" (or higher) board across each end at 90 degrees to the saw, and a wooden jig that looks like a 90 degree isosceles triangle, you can cut one or a dozen pieces of wood to exactly the size you want, and fast. With one more simple jig you can cut dozens of pieces of wood to exactly the same size with angled ends for picture frames. When using a slide table you can not only do all kinds of jigging easily, the wood you are cutting stays in one place on the slide table and it is the entire slide table moves past the saw blade. No catching on edges of the saw, no thin pieces dropping down between saw blade and table, etc., etc. etc. By the way, for those of you who are not familiar with table saws, the 4" or 12" or 7" referred to at the beginning are the diameters of the saw blades used on particular table saws. So, a "7" table saw" is really a table saw with a 7" diameter blade. Last time I looked Micro-Mark sold slide tables for the Dremel 4" saw that are ready made. If you ever buy one, email me after you receive it and I will tell you what small piece of wood to add to greatly increase its safety. Bob, Sears sells metal rails that fit the 7" saw table slots for making your own slide table for a larger saw. If you don't understand all this and need to, feel free to ask questions. Barb Jones, Cupertino, CA |
Miniature Saws: I see a lot of talk about miniature saws. Well I use the Preac table saw and feel it is the best investment for your money. It is precise, quiet, and as safe as you will find for miniature work. I purchased mine from Smaller than life after taking a furniture course from Pete and Pam. I also have a dremel and Vanda-lay industries offers a duplicator, lathe, and mill using the dremel but I never gave them a second thought. I lost the URL long ago. They have a gang saw attachment for either the saw or milling machine (not sure which). I opted for the Preac because I tried it and knew it worked as advertised. I never felt comfortable using the saw blade on the dremel. The saw blade on the dremel does not have a diameter large enough to extend past the body of the tool and if you were to put a larger blade on it and run it full speed I don't know if I'd want to be in the room. The dremel is very noisy also. Now that said, I find my saw is capable of most chores I want to do. However even it falls short on the rare occasion(no tilting arbor) . The point is I feel if the Preac with a wealth of attachments comes to the wall on occasion then an adapted Dremel with limited fixtures and support will fall short much more often than not. Earth & Tree carries the Jarmac and Tom can probably answer all your questions. I suggest you talk to people like Pete at Smaller than Life or Tom at Earth & Tree (or your local dealer) that know what demands are put on the miniature saw before investing any money. A saw is more than holding something down and spinning a blade!!. If you want to extend the capabilities of your Dremel buy the flex shaft for it. It won't give you a saw but it will open up a whole world of new uses. Another Idea is a club could pool their money and invest in a saw. How to share it would be the problem. I think temporary access to a real saw would be more productive and safer than a jury rigged setup. I bought a Dremel lathe, tried it and was disappointed. I waited a year and purchased the Sherline. I was lucky in that the old Dremel came at an inexpensive price so I was able to determine I liked working with a lath and got to make a few items without risking a lot of dollars. Here's my list of key things to consider: Safety- even miniature power tools can inflict damage. Support- will they be there if you need help and advise ? Usability - I have a friend bought a lathe and now can't find chucks. What options and tools are available? This list represents the things that some do not consider, but will surely take the fun out of a purchase. Bill |
Microbrushes: are available at Nancy's Notions. They are great people to deal with. They mostly carry stuff for the seamstress, quilter, etc., but they also have some craft type things. They have a paper catalog that you may obtain also. I have ordered things from them several times. She is in Beaver Dam, WI. http://www.nancysnotions.com/ Another company you might like to try is Clotilde's. http://www.clotilde.com She carries all sorts of sewing and craft items. I think she is out of Florida. Two others you might like are Home-Sew and Newark Dressmaker's Supply. They are both out of Eastern Pennsylvania. Home-Sew has an online catalog and Newark has a paper catalog, but you can order online out of the paper catalog. http://www.homesew.com/ http://www.newarkdress.com/ Marcie |
Microbrushes: can be purchased from the MicroMark Catalog p. 70 of Winter 2000 catalog(1-800-225- 1066) Web address: http://www.micromark.com Priscilla |
Gluing resin: I have had good luck using JB Weld to glue resin to resin, it is available in hardward stores. Nancy Clark |
Power tools; Smaller Than Life carries the line Preac table saws, Sherline metal working lathes and Carbatec wood lathes and duplicators. We also present workshops using the table saw at a number of shows and at our shop in New Hampshire. There is also a complete line of hand tools for the miniaturists on our web site. Sorry, no shopping basket, just the phone and good old reliable e-mail. http://www.nh.ultranet.com/~smallife Pam & Pete Boorum, On Sebbins Pond, Bedford NH |
| Previous 10 | Next 10 Page 962 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |