Aging fabric, plastics and woods with files: I don't know how many of you use files in making miniatures. I use them  for almost all phases that require finishing. Wood, plastic, metals etc.  I even use them on fabrics to age them. This brings me to my hint.

Many things clog up files and many people toss the file when it seems to be useless. I find mine plugs up with solder or lead when I am working those metals. Also I find them plugging up when I am finishing the edge of wood or a piece that has been glued.  Many times super glue or epoxy get into the teeth of the file or even rust.

There are brushes called file cards that are available to clean files. These are  flat wire brushes with very short bristles on them. Supposedly they take out the dirt and stuff. I find these don't always work.

Here is my hint. Use a short length, about two inches, of 1/4' brass rod. Chuck it into the handle for and X Acto saw. File the end to a flat wedge shape.  Not a cone.  Now hold on flat side so most of the point and one side is in contact with the file teeth, sideways. Push the brass back and forth across the file, with the length of the file teeth until the file makes a bunch of little ridges in the brass. You will notice as these ridges form they ride in the teeth grooves and cleans all the trash out.  It even works to remove  heavy rust from the file. In the end you have a clean sharp file again. I have used this method to save some really bad looking files I got at a Flea market with box of other tools.

Bill Hudson, Eugene, Oregon


Cutting Angles: I have the MicroLux scroll saw. It has the attachment for cutting angles... I couldn't figure it out either until my cousin's husband, who makes beautiful real size furniture for his home, came to visit and showed me. First you set the angle on the gizmo (it kind of looks like a protractor) and tighten the knob on it. Then you put the wood in place and, finally, you slide the attachment in the groove that the saw has on the right hand side of the table. When you slide the attachment the wood will automatically take the angle set by the gizmo.

Nertha


Faux tacky - put some white glue into an open jar and leave the lid off for a few days - the white glue thickens and you can control just how thick you want to make it. When it is about right for 'tacky' put the lid back on!

Another use for white glue is to make something that looks just like blackened metal (a little like wrought iron). You cut your pieces out of brown paper bag, coat it on both sides with the glue (messy) and move it back and forth through a candle flame. When it is bubbled and dry, repeat (3 times) and while it is still warm (careful of fingers) shape it as you wish. When it is cooled you can leave it as is or coat it with RubNBuff and you will have a great antique effect. We used to make flower petals like this and then attach the finished blossoms to drift wood. I am sure this could be adapted to minis.

Jacqui Marlin


Brad Nailer and Air Compressor: http://www.grizzley.com http://www.amazon.com (yes the book people carry lots of tools and only charge $5.95 for shipping) Also look in your local classified ads under tools. That's where I bought my first one.

Tom Berkner


Gluing Foundation: I would suggest getting a bottle of Weldbond (this is its brandname). It's excellent, and somewhat more tacky than wood glue (yellow). While you're at the store picking up the Weldbond, also buy different widths of masking tape. This is what will give you freedom from standing there for 25 minutes until the glue sets. The Weldbond will also have to set, but because you'll have the masking tape holding the corners together (do this to both the inside of the corner and the outside) it will set tighter and there will be less movement. Also, if you have Lego building blocks around, build a bunch of the larger and wider ones up in a stack and use that inside the corner areas you are putting together after you have glued and taped. Just fit it in, readjust your 90 degree corner and don't take the tape off for a good long while. When I'm gluing, I use masking tape to even hold down the window frames while they are gluing. I'd rather have to sand/repaint a small area that has the masking tape left (which doesn't happen too often unless you leave it for days and days) than to have corners out of whack and crooked window frames. Never use hot glue!

Joy Perkins in Pointe Claire


Gluing Trick: After you've spread the wood glue on the joint, put a drop of regular (not gel, not pen, not anything else but regular) Super Glue every 4 inches or so. The Super Glue will help hold things in place while the wood glue dries.

Trish in San Jose, CA


Clamping Corners: May I suggest that you try using a picture frame clamp? You can set up all four corners at once using one of those. I have been using Elmer's carpenter's glue for years with great success. Once that glue sets up (under clamping pressure) it is usually stronger than the wood itself! I also strongly recommend attaching the corner joints with small brads or screws, then use a carpenter's square to square everything up. You can countersink the brads or screws and back fill with light weight spackle. Cover with your final surface treatment and you'll never know that they are there.

Lloyd Cooper


How I photograph my minis:

1. If I am photographing a house, or roombox it goes right outside and sits on the beauty bark. The scenes in the yard are slightly fuzzy thus not too distracting but allow for good light and a Puget sound/mountain backdrop.

2. if I am photographing a set of room furniture, There is this little spot right off the yard... it is a raccoon trail (I am sure you have those in Puyallup) and the ground is solid. The indentation they made in the greens gives a gentle shading of direct sun and looks just like those adds for Ethan Allen furniture (you know the ones... beautiful bedroom suites in the woods)

3. Individual pieces can also be shown this way, or If the weather is icky (like it is today) I put it on a piece of fabric (I never worry about wrinkles) or paper. That velveteen paper from the scrapbooking store would be great. I am guilty of making sure the backdrop compliments the piece I am doing. White painted wood gets a dark forest/sage green backdrop... stained woods get pinks, lt blues, or peach depending on the finish color/upholstery... the other thing I do is use scaled wallpaper (on artist board from target) and a penny.

Do those things help? You can even head to your local state park and photograph there, they have great maintained trails and old forest that makes for great back drops.

The other thing that is a godsend is a digital camera. I would have spent thousands on film if I had actually had to print out before I knew what I was doing. Now I preview on the LCD panel and trash what I don’t like right off, and it stores 300 pix (1280res) per smart card.

Sudie Parker


Mini Family pictures: Are the pictures in black and white? And, do you have a copy place like Kinko's near you? If so, all you need to do is take your pictures to a copy center and use the 'reduce' buttons on any copier until you get a picture that you can use in miniature. (If they are sepia toned, still use the black & white copier until you get the size right...color copies are much more expensive, and then use the color copier to take your copies.) If you want sepia toned pics, use the a parchment colored paper in the black & white copier.

Kaye in L.A.


Mini Family pictures: I have gotten my family photos miniaturized at Mail Boxes, Etc., but Kinko’s could do it, too.

I took in all of my old family pictures, told the guy how small I wanted the pictures and he did the work on the color copier, until it came out the size that I wanted. The photos came out about a half inch to 1 inch high and you could still make out who was in the photo, so I made my aunt a miniature photo album and she couldn't believe how small the pictures were.

There are probably other ways, but this is how I have to do it, because I don't have any other way.

Sherrydon


Previous 10 | Next 10


Page 964 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)