Glue for Chrysnbon kits: Go to the toy department in most stores, where the airplane and car model kits are, and you'll find "Plastic Model Cement." It’s the same thing that used to be called "Airplane Glue" but without the fumes that the kids used to sniff to get high. It will work perfectly to glue your Chrysnbon. If you have a Michael’s in your area, they also have models and glues and carry a Glue Pen that is made specifically for models. It will give you great control over your glue on small seam lines.

Tere Perry


Gluing plastic: My personal preference is Methyl Ethyl Keytone (MEK) it smells right strong and probably kills brain cells by the millions so use it with good ventilation. dries very fast and holds great I have plastic I glued 30 years ago and it's still strong. You can get it a any hardware or Home Depot type store just use a small brush to apply.

Rik Pierce


Shingle-glue/tape wire paint: I used Liquid Nails for my cedar shingles.  It comes in a tube and you just apply it to the roof, and then sort of put the bottom of the shingles in it.   I did also stain all my shingles before putting themon.  I put some stain in a plastic container, put as many shingles as I could in the stain, let them sit for the allotted time, and them strained the paint into another container.   Put shingles in the second container and wiped off the first batch and did that until all that I needed were done.    The roof is on my website below on my Little house on the prairie post office. Traci, I also stuccoed over the roof and the tape wire in the post office and the electricity still works! So paint should be no problem!

Isabel Allen


Light Box: I would like to pass along a rather simple idea or two.

1. Set a small lamp on the floor (no shade), between your legs, then hold a piece of Plexiglass or regular glass on your lap and trace away! (It won't work if you wear a skirt, especially one of those long ones that are in fashion right now.

2. Put 4 cans on a table (fruits/veggies, whatever, as long as they are the same size) and lay a piece of Plexiglass or regular glass over them with a regular light bulb (like a trouble light) underneath.

Linda


Tool Recommendations: I'm a miniature woodworker and much prefer power tools to hand ones (I have 3 nice stitches in my finger to remind me of the utility knife slip!). Check my website http://members.tripod.com/miniwizz I have a page on "tools and supplies" and a detailed list of tools I have. They were purchased over a period of years, so start small (no pun intended) and add to your toys over time.

Jan in Charlotte

Making Jigs for Minidrills: About a month ago I picked up a book from Amazon.co.uk. called 'Minidrill' by John Everett. There are 15 projects telling you how to use the various drills, burrs, etc; and at the beginning of the book there are three attachments to make using the minidrill itself to build them. A lathe, a drill stand and a router table. The cost of the book was very reasonable and would repay purchasing even if you only made one attachment. A great help if you mini on a mini-budget.

Maureen in Hemel, UK


MINI STUFFED ANIMALS: I've only made a couple of these, but along with tweezers, I used a stylus? Embossing tool? Maybe someone can help with the name of this-it's got a wooden handle with metal, ball-shaped tips on either end. I know it's a Very Important Tool in my mini toolbox!

Cheri


Glue Recommendation. I use E6000 for a multitude of things. It really bonds well for unlike surfaces, china, glass and resin.

Deb


How to make a mini lampshade: Determine the desired diameter of the top opening, diameter of the bottom opening, and height of the shade. Find or make 2 wire rings, one for the top opening and the other for the bottom opening.  Measure carefully.

On paper that is not going to be the lampshade, make a diagram (If only I could draw on the darned computer!) as follows:  Make an inverted "T", i.e., horizontal line with perpendicular vertical line going up from the center point.

Mark the intersecting point"A." Measuring from that point going up the vertical, mark the height of the shade as "B."  (The vertical will need to be higher than that point, so if it's not, elongate it.)
Mark the width of the bottom opening on the horizontal line, with A as the exact mid-point.  The outer points will be "C" on the left and "D" on the right.

At point B, and using B as the mid-point, mark the width of the top opening with points "E" on the left and "F" on the right.  This will be parallel to the bottom horizontal.
Connect C and E, continuing that line until it meets the center vertical, and then do the same with D and F.  The point on the vertical where they meet will be point "G."

Cut a strip of cardstock (index card works well) about 1/4" wide x 3" long, depending on the height and size of your shade.  Down the center of the strip, mark three points to correspond with points G, E, and C (or G, F and D -- same diff).  Put a decent-sized pin hole (large enough to accommodate a sharp pencil point) at points C and E.
Pin the paper you will be using for the shade to a piece of cardboard, cork board, or other surface to which the paper can be pinned.

Put a straight pin through point G on the strip, and pin it to the lampshade paper. With a sharp pencil point in point E on the strip, and carefully keeping the strip attached to the paper and board at point G, draw a large arc.  Make a complete circle if you wish; you can always trip later.
With the same sharp pencil (or a different one -- knock yourself out!) in point C on the strip, make another large arc or circle.  BINGO! You now have the correct shape to cut out.
To determine the length of the paper, measure the circumference of the two openings, and then measure out the same distances on the respective arcs, keeping the beginning and ending points of each arc in line with good old point G.  Don't cut on these lines, though; leave a bit(1/4"-ish) to overlap and glue.

Glue ends together to get your conical shape. Using thin strips of tape -- and a lot of patience -- tape the metal rings to the openings.

Rosemary


Quilt Display Rack: How about using one of those tie racks or belt holders that you attach to the inside of your wardrobe?   They flip from side to side (not the ones that go downwards). You could snip off the hook part, get some thinnish doweling, drill a hole and slide over the remaining stump.  I know we used to have one that I threw out when we moved and it had a double layer of hooks on it.  It was quite long - about 10" but you could always cut them down to size.

Yvonne


Hot Glue: I agree with not using hot glue in constructing dollhouses. Not too long ago, I helped refurbish an old dollhouse. In that case, I was glad it was constructed with hot glue, because EVERYTHING popped off with a little pressure from a screwdriver. So, I guess if you plan to rebuild your house someday, then by all means, use hot glue. If not, then use a good carpenter's wood glue or QuickGrab.

Anita Myers


Previous 10 | Next 10


Page 969 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)