Hot Glue: I have heard stories of people redoing dollhouses that had been partially assembled with hot glue. To start over and redo them, they just used a blow dryer and the hear softened the glue and the houses came apart very easily. I know some kit manufacturers recommend hot glue (Corona and Greenleaf), but no experienced dollhouse assembler does!

Anne Gerdes


Blind Cut: A blind cut is a cut started away from the edge of the wood being cut. It can also be called a "plunge cut." Example; As I used a plunge cut, using a power saw, I would pull back the blade guard so the blade was rotating unprotected (Not to be done by neophytes) I would take the saw in this fashion and lower the blade onto the line I drew for the cut. A much safer demonstration is to take a piece of paper or thin card stock and poke a scissors in the middle of the material and start to make a circle-cut. Of course you can always fold the paper and cut the center hole in that manner but its impossible to do that with wood.

Bob


Quilt display rack:  Have you ever gone into one of those stores where they have the full size area rugs hanging on racks that you can leaf through.  That would be the same idea.  Also I think they use to have a thing like that to hang towels on.  It had a metal plate that was flat against the wall in the vertical position and they had metal arms that stuck straight out staggered one above the other so that you could fan them out to either side.  I would take a thick piece of wire and bend one end into a small L.  Drill a hole into a piece of wood and insert the wire through it so that the bent end caught right behind the hole.  If the hole was large enough or make a slot to either side and it should be able to move from side to side.  Although you would have to hold your wooden piece out a little from the wall so the metal leg can move.  That is just a rough idea.

Elizabeth


Danger of shop made circular saws: Unless you are very careful how a Dremel tool is mounted and how the circular saw blade turns relative to the work, a shop made circular saw can cause accidents. Think of how all the miniature table saws are made. A portion of the blade extends through a horizontal table and the work is guided by either a sturdy rip fence which is parallel to the blade or a miter arm which is perpendicular to the blade. These hold the work solidly against the rotating teeth.

Among woodworkers it is universally understood that pushing lumber through a table saw without either a secure fence or a miter arm guiding the work is inherently dangerous and can cause kickback and nasty cuts. Kickbacks cause accidents.

Incorporating the elements of fence, miter arm and flat, secure table into a shop made Dremel jig is a difficult undertaking. Unless you know how to do this safely, I don't recommend making a table saw out of a Dremel Moto-Tool unless you have a lot of mechanical experience and understand all the forces at work.

If you can't afford to purchase a miniature table saw, either cut by hand or buy an inexpensive scroll saw. Learn to plane the edges straight and square. That's how all the great 18th century furniture makers worked in full scale. I think it makes more sense than getting stitches.

Many of you know we conduct many workshops using Preac table saws. We sell exclusively Preacs which we like the best for making furniture. The Jarmac, Micro Lux, Unimat and Dremel table saws are also safe to use and cut effectively. Personally, I leave the design of such things to the experts.

Someone mentioned using a larger table saw. I use a 10" Delta Unisaw to re-saw lumber, cut ply wood and occasionally cross cut miniature lumber. The thinnest blade available for a full size table saw is 3/32<.093> inch thick. I regularly use a 2-1/4 inch Preac blade .020 or .028 inches thick. This requires much less power, much thinner throat and is very safe. Making miniature with a full scale saw may be perfectly safe, also, if done properly. The margin for error is less than with the smaller, less powerful machines and the consequences of a mistake are likely to be much more damaging.

Pete


Dremel saws: Bill is talking about a Dremel hand held Moto-Tool (like a carving tool)and various ways to adapt it. He is absolutely right that you must not put a larger blade than Dremel's old 1" diameter blade, or the 1-1/4" Gyros blade on the Moto-tool in any setup. The speeds at the rim can be too fast, the blade disintegrates, and you are in danger.

HOWEVER, the Dremel 4" table saw, which several of us were talking about, is a real table saw designed to be a table saw and designed to use the 4" blade. Used properly it is no more or less dangerous than any other table saw ever sold.

Barb Jones, Cupertino, CA


Repairng Older Dremels: I have located a company that may be able to repair older Dremel tools. I understand it is not associated with Dremel Corp, but run by a relative of the man who invented the MotoTool. A catalog is available at no charge. Dremel Repairs, 4631 East Sunny Dunes, Palm Springs, CA 92264 619/327-3003 http://www.dremel.com

Dean Jenson


Quilt display rack:  Go to your wardrobe and look at your skirt hangers. Several of our rug shops here hang their rugs on equipment that looks very like skirt hangers. Our $2.00 shops sell very small pegs.

Raeleyne


Dremel Jig Saw/Scroll Saw Blades: These blades have a short pin at either end that hooks into the arms of the jig saw above and below the table. At one time I did see pin-end type blades at our local Sears store. They are also available from Scroller, Ltd, a catalog for scroll saws. Their telephone number is 1-800-486-6053.

The blades originally packaged by Dremel came in two flavors - coarse and fine. If currently available with these options, go for the fine size. I never did use any of the coarse variety when I used the Dremel.

Pam


Lathe substitute: You can use a variable speed drill press or a regular variable speed drill held securely in a vise as a lathe for simple short turnings... if you are turning small stock use the adapter for tiny drills to hold the wood.

Sammy


Microscope & Musical Instruments: I found an odd little site, www.veghead.com, which has a huge assortment of the mixed-scale brass miniatures -- including a 1 1/8" microscope for considerably less than the HBS version, but of course you'd have to make your own case for it. Veghead also has a large selection of musical instruments, although few of them were 1:12 scale  (Most would be right for a Barbie orchestra) and quite a few egg stands, for those who like them as table bases.

Loretta


Previous 10 | Next 10


Page 970 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)