Dremel Saw Blades: I needed some saw blades for the discontinued saw and contacted Dremel directly. They said they have about 6,000 left. I got six of each, which I figured will last me to the next millennium. Anyway, your local Dremel dealer can order them for you, or you can go to their website: http://www.dremel.com.

Sharon Begley


Rosary pliers - rosary pliers are what you need for making round loops in wire. I've seen them at craft stores and WalMart in with the flower arranging supplies. Pearl Art and Craft and JAF also carry them in a little better quality.

Rose


Painting Tip: A piece of foam (like that used in shipping) goes a long way for those painting projects. I cut it into small, odd-shaped pieces and it gets into all those crevices. Forget those expensive foam brushes!

Janet Gorelick


Strong Glue: Just found a new glue at the home improvement store. It's Elmer's polyurethane glue. It's expensive but worth it! I build mini furniture and this glue is unbelievably strong.

Janet Gorelick


Pliers: Available from Ron Stetkewicz, HCR 1 box 61B, Cairo, New York 12413, (518)622-8311, email: Skhardware@aol.com. He also makes wonderful brass hinges.

Bill Leimberger


Glue Tip: Use hot glue to hold something temporarily, and Aleene's glue to hold it forever. When gluing on trim and other things that can be hard to clamp, use the combination of the two. Use a dot of hot glue and then draw a line with the Aleene's glue. Don't try to mix them, alternate them. It works great. The houses don't fall apart in the heat and you can still get some of the benefits of the hot melt glue and fast action.

Deb


Miniature Planers: Turning a door planer into a miniature planer: Over the years there have been a variety of attempts that we know of to make a miniature planer. As far as I know they have all failed. I used an Inca full scale planer for years to plane down to 1/32 inch until I changed from flat sawn to quarter sawn lumber for grain appearance and stability. With the quarter sawn lumber most of the work went into the dust collector. Incidentally, Bill Robertson also uses this machine to plane very thin material with a backing board. He tells me the results have a great deal to do with the positioning of the stars and other celestial bodies.... Sometimes it works and sometimes it doesn't.

For the last three years I have gone directly from resawing to the thickness sanding without using a planer. I use a Woodmaster sander for big runs. It is hard to change abrasives and destroys sandpaper frequently when a thin end of the wood gets caught under the paper. That method is time consuming and replacing belts is expensive. You have to make sure the bow of the wood is up. The results are good and there is little waste. The only disadvantage is that it dulls saw blades faster. One of these days I will buy a better thickness sander with a variable speed belt feed. Big money!

I use a Preac 4 inch thickness sanding machine for small batches. It works fine with very little waste but it is quite slow. Without even getting into the safety issues, I don't think a hand held door planer would work at all on thin material. There is no good way to incorporate a system to hold the strips of wood down. There is no way to feed. There is no way I can think of to make a jig accurate and rigid enough to plane plus or minus .003 inch, what is what you need in miniatures.

For an alternative, you could buy a Makita or similar thickness planer which would work OK down to about an eighth of an inch or even thinner depending upon the wood species, moisture content, grain and the position of the stars. You would need to use a backing board. I use Melamine because it is slippery.

You can buy a small Preac thickness sander that will work under 1/64 of an inch. I reduced a run of 20 or so sheets of paper backed veneer from .020 to .015 inch without any waste once I figured out how. This machine only has a 1/8 HP motor and I think it would be hard to hurt yourself with it. This is how I do all the exotic wood we use for boxes and inlay. This machine will use a shop vac for dust collection which you absolutely need with a thickness sander or planer. Equally essential when sanding exotic wood, to keep it out of your lungs.

Pete


Glue tip: Another really good way to glue your house parts together is with a line of tacky glue spread thin with your finger and then with drops of Super Glue interspersed along the line.

Roz


Bandsaw Tuning: Bandsaws need careful tuning,which at first may seem a pain but when practiced a bit comes easily. Not only must the blade tension be adjusted correctly as previously mentioned but also blade tracking and the blade guides. If you have the directions for the saw, read them until you understand them. Practice the steps several times and follow them religiously. I hated my new bandsaw at first but then got smart and learned to use it.

Don Dickens


Rose-Making Tool: I made a rose-making tool by filing off the top of the eye of a large needle, then heating the pointed end of the needle and sticking it into the end of a large glue stick. It's been five years now and the needle is still imbedded tightly. It isn't the least bit "sticky" to the touch and it cost almost nothing to make.

Darlene on L.I.


Previous 10 | Next 10


Page 971 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)