Picking up stuff: Those eyeglass foam nose pads might be perfect to stick onto the inside ends of an old tweezer. That way you'd have better hold for slippery mini things. Maybe you'd have to widen the tweezers' opening distance and trim the pads somewhat to fit your tweezers. It might be worth trying. Also, I often use the moistened uncooked spaghetti trick to pick up minis, but I think the drawer knobs might be too heavy for it. Darlene |
Micro Mark Mini Power Tools: I have three of the MicroMark power tools. The jigsaw is ok as long as you don't try to saw through anything thicker than 1/8". I have managed quarter inch stock but very slowly (this was plywood though). The orbital sander is great. I bought an extra snap-on pad so I could have fine and course grit paper ready for use. I probably use the drill most. I keep it plugged into the variable speed transformer all the time for easy access. These tools are so small you can keep them right on your workbench. I've enjoyed using mine since 1989, no problems with any of them so far. They seem to be very well made. Susan Wise in Denton, TX |
Cutting Tips: ** Use a sharp knife ALWAYS ** Replace or sharpen blades often ** X-Acto blades (or similar) can be sharpened using an oilstone - in fact I think some "X-Acto-type" blades benefit from being sharpened before use. ** Use the right thickness blade - a surgical scalpel type blade is great for cutting but for thick stuff, especially Foam Core, which has a soft inside, use a heavier blade (e.g."Stanley" knife or the heavy duty X-Acto) A too thin blade on thick material will waver, giving you a perfect straight line on one side and a wavy one on the back. ** Use a steel rule to cut against, ideally a cork or foam backed one (so it won't slip) with a raised finger ridge (so if you do slip your fingers are protected) ** Cut in several light swipes, extending the full length you want to cut (stopping part way will look wonky- trying to cut through the whole thickness in one slice will go wrong) ** Use a good quality cutting surface - those green self healing mats are good (get from dressmakers supply stores) Sanding Tips ** Use very very fine grit sandpaper. I mostly use 320, 600, 1200 grit. 220 is my heavy grit ** Final "sanding" is with a scrap of nylon stocking/pantyhose or brown paper bag. ** Put the item you are sanding on the work bench and hold the sandpaper ** Use a sanding block to avoid sanding a dent into the middle where your fingers pressed down ** Hold another piece of the same thickness stock next to the bit you are sanding and sand right over the top of the two of them (avoids getting edges thinner than the rest and clamps those @$#%&!! tiny bits in place) Sandra Monk in New Zealand |
Miniature Tools: For those who might be interested, Sears has a kit of miniature tools that look just like Micro-Mark's (pages 6 and 7 in Micro-Mark's current catalog). I believe these are made in Germany and retailed through several outlets. Sears has the name "Craftsman" on theirs, but I would be hard pressed to say they weren't one and the same as Micro-Mark's. I didn't pay quite as much at Sears. Sears sells them as a kit and they even have their own heavy plastic carrying case that holds all of the tools. The little stationary table attachment for the jigsaw comes with the kit also. The transformer, router, jigsaw and orbital sander make up the kit. There is a place for the drill, but it does not come with the kit. Not all Sears stores carry them, but you can have them order them for you. I really like being able to have all of the tools in a case, as everything is in one place when I am ready to use them and they travel very nicely with you. They also include jigsaw blades and sandpaper to get you started. Don't expect them to do the job that a regular size tool will, but it's every bit as exciting to power up that little jigsaw and hit the wood with it! Lynn in AR |
Something for cutting angles other than 45 degrees: I hesitate to suggest a hand tool costing thirty US dollars, but the Dobson Mitre Right would sure fill the bill. It's a handsaw set in a frame allowing it be swung in an arc and then fixed in place. Hobby Builders Supply's on-line catalog has a good picture: Mary in Oregon |
Glue for light fixtures: I've lighted more mini homes than I can count, and I've found that silicon or Aleene's tacky do just fine and don't damage the wiring. I've always used masking tape to hold in place for at least 24 hours. There are times when you can't tape it, so find items around the house to hold it in place for 24 hours, like a drinking glass, jar of peanut butter, etc. Just be sure not to use glues with acid that will eat the covering over the wires. I want to strongly warn against using Superglue or Quick Grab (these are what I referred to as glue with acid) when doing lighting. You may be very careful and put just a drop, but remember others won't always be so careful. I don't ever use any type of Superglue as it will eat through the insulation on the wire and it will also discolor the metal of the light fixture over time. Patience with white glue is the safest practice, and there will be no damage done to your expensive lights. Jinger |
Gluing light fixtures: Try using bath tub caulking - it will adhere to anything. Just a small wee drop is needed. Or go to an auto supply store and ask for the glue used to affix a rear view mirror to the windshield. That stuff sticks to glass also, like the caulking. Bob in Hollywood, FL |
Gluing light fixtures: Be careful about gluing in ceiling fixtures. Glue them only if they have replaceable bulbs. If the fixture will work we prefer to use Circuit's chandelier adapters and sconce adapters. One type, you glue a part of the adapter to the fixture and then it snaps into the adapter which pushes into the tape wire. Another type slides over grommets in the tape wire. Both are a lot easier to use than trying to glue a fixture to the ceiling and wall. Another plus is that it makes your fixtures removable, interchangeable and replaceable. I like "ables." You can get them at most miniature shops either in person or through the mail. They are about $5.00 each. Well worth it. If your fixtures don't fit the adapters or you don't want to spend the money, try using poster tack. Get it in white at Wal-Mart. We cut packages into small squares and have them in our shop for our customers' convenience. It won't melt in the heat and works great on miniatures. Sandra Olsen |
Resealing the caulk tube. I have tried the nail trick with less than satisfactory results in the past. Don't know what type of nail I used but it rusted and discolored the caulking. Now I use an electrical connector like you use to connect two wires together. Get the right size and screw it on tightly. I learned this on the House Doctor show on HGTV and it really works! Linda in Georgia |
Doll Hair Glue: I prefer Aileens Tacky, or Velverette. Viola Williams |
| Previous 10 | Next 10 Page 972 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |