Doll Hair Glue: I do a lot of wigging and also teach it. I have found that Aleene"s Tacky thin bodied glue works the best for me. Because it is thin, a straight pin can put the tinniest bit down to hold a curl and not show. Because it is tacky, it holds that curl until dry. When totally dry, if you hate the look, or a child decided to play with the doll, the entire wig will peel off in one piece. It can also be soaked off in water. The glue comes in the gray bottle. Get the smallest bottle, a little goes a long way and it goes bad in heat after a while. |
Doll Hair Glue: Use Velverette...it is formulated for use with fabrics. It can be described as a thick, white, tacky. The "for use with fabric" part makes it clear drying and flexible. While we are on the subject, use only a hatpin or pointed tool to push the hair firmly into the glue. If you use your finger you will leave large glueprints. Laurie Sisson |
Make a Bar Clamp You will Need: 1 full-threaded bolt. Length of bolt is going to determine "span" of clamp. Diameter of bolt is not important What I do: Place one of the large washers on the bolt and slide it to the head end. Place second washer on bolt and then thread on the wing nut. The space between the 2 washers is the "span" throat) of the bar clamp. Place the items to be clamped between the 2 washers and tighten the wing nut. Bob in Hollywood, FL. |
Glass Cutter: Some thin glass can be cut with the usual cutter you find at the hardware store, but I got hold of some that needs a better cutter than that. When I tried to cut it with the usual cheap cutter, it broke everywhere but along the line. I ruined a lot of glass before I found a better cutter. The better cutter I found was from a stained glass store. It has a hollow handle that holds extra oil, and makes a cut that the glass breaks cleanly along. So if you don't have luck with the cheap cutter, try this one. Jeanne in San Anselmo, CA |
Doll Hair Glue: I use Tacky glue - the thicker, the better. Michelle Geoffrion-Mahler |
Gluing Glass: There is an automotive glue that is used to glue the inside rear view mirror to the windshield. Holds like steel. Very reasonable. I do not know the name but just tell the person at the counter that you want to glue your rear view mirror back onto the windshield. Bob, Hollywood, FL |
Storing Paints/Stains: To help paints, varnishes and things in a bottle or can from drying out - store them upside down. The liquid in the container acts as its own seal and stuff will stay like new. Susan in St. Croix |
Cutting circles: You can make an easy jig to cut circles. Assume you want a 2" circle. Clamp a board 1/4" thick or so to your saw table with a nail sticking out of it a short distance. The nail should be about 7/8" from one edge, that edge should be parallel to the saw blade. Take a piece of the wood you want to make into a circle and drill a small hole (or pound a nail or other sharp object into it) exactly 1" from one of the edges. Place that edge against the blade, the hole over the nail, and turn the wood around and around. Voila, you have a circle of wood. Barb Jones |
Miniature iron: In the last Keepsake Quilter newsletter/catalog I received there is a Mini Iron. In the product description they refer to it as an itty-bitty iron. The handle is 9" long and the ironing surface is 1 3/8" long. The handle is similar to a curling iron handle and at the end is a mini iron. I can send you the catalog if you like. Melissa |
Miniature iron: To find a smaller than usual iron, check out travel irons. When I was hanging out with quilters, they often used them in classes, they're smaller, cheaper, and some are quite good. I bet a curling iron would work, too, and some nowadays have a steam option besides. Bonni C Backe |
| Previous 10 | Next 10 Page 973 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |