Attaching Shelves to Walls: I used Elmer's Wood Glue to hold cabinets, pictures and mirrors. I sanded the area where they were to attach, then placed glue on both surfaces. I waited a couple of minutes and then held them together tight a full minute. Or, try Crazy Glue. It holds a man in midair, so it might hold cabinets as well.

Leslie


Cutting circles: The easiest way I ever found to cut circles was to use a Dremel Moto-tool in a Dremel drill press.  I made a jig with a plywood base that can be clamped to the table, and an acrylic "spinner" that turns on a pin exactly under the bit.  I use a long, thin bit (sorry, the Dremel number has fled my mind, but if you are really interested after you read this, I can get the bit number for you), draw the circle I want lightly on the first piece of wood, double-stick-tape (from the stationery store, NOT carpet tape) the wood to the center of the spinner, move the Moto-Tool out to the edge of the circle and lower the bit a little at a time as I spin the spinner.  It cuts through the wood and you have a perfect circle.  Take the spinner off, remove the circle, tape a new piece of wood to the spinner and do it again.  Takes a little time and patience, but the pieces are perfect.  A little sanding and you are all set. 

Note:  I make the spinner perfectly square, scratch lines from corner to corner to find the center, cut the wood square and match the corners of the wood to the scratched lines to center the wood under the bit.

Jeanne


How to Handle Quik Grab glue: I set the tube upright in a small jar.  That way when you take the lid off it is not as likely to ooze so much.  Then I take a toothpick to get the amount I want from just the very tip of the jar.  Not perfect by any means but makes it somewhat easier to control.

Dorothy


Quik Grab: Here's a little hint that I got once from one of my students. (I'm always learning from them, one of the pleasures of teaching!) If you take the end of the metal tube and squeeze it with a pair of pliers so that it becomes an oval instead of a circle, the stuff doesn't run out on you as badly. Now don't overdo it and close the end completely.

Next the solvent for Quik Grab is mineral spirits. If you wipe off the end of the tube with a paper towel lightly soaked in mineral spirits, you will be able to get the top off and use the tube again. Also lots of people think it works like other glues, just put some on and your parts will stick; but that isn't true. Quik Grab is activated by pulling the pieces back apart and reapplying. The more you do it the faster it seems to grab hold.

Shannon Moore


Cleaning Oil-Based Stain from Brushes: Just wash out your brushes that you have used with oil-based stains with plain old soap and water. I usually use dishwashing liquid. They clean up very well and you don't have to worry about ruining your brushes or having them burst into flame. Just pour a little soap in the palm of your hand and scramble the brushes around in the sudsy mixture. You may need to repeat this to get them really clean.

Dottie


Quick Grab: I like it for many jobs:   Siding sheets, moldings/trims, etc. I even used it to repair a broken glass dish once - YES, it will glue glass!

Quick Grab is air-activated, so once the tube is opened, it will 'dry out' over time. I try to always squeeze from the bottom of the tube (yeah, I do that for toothpaste, too - LOL), and force out as much air as I can. I store mine upright in a small glass jar and put it back in the jar even while I am using it. This helps keep the glue from oozing out while open, between applications. I use my ever-handy baby-wipes to clean off the open end during and after use, and they help clean up spots on my fingers, too.

Laura


Tiny micro hand held jigsaw: I bought mine from Micro Mark. They have an entire selection of hand held tools and are wonderful for smaller scales and delicate wood.

Sue Thwaite


Cleaning Oil-Based Stain from Brushes: I just throw my brushes in the regular garbage once they have dried. I use sponge brushes for larger projects and sponge-tipped eye make-up brushes for the smaller projects. Our local waste disposal company has no problem with this.

Pat M


Easy way to pick all eentsy teensy tiny mini stuff up is with a raw spaghetti noodle, slightly wet on the end. Touch lightly to object, then place object in glue on surface, and the glue will "grab" it away from the noodle.

Kay Baughman


Minis Lathe Turning Class - Rolling Pins: The first actual turning class has been posted on our web site (www.vandijkminiatures.com).  This class provides instructions for turning a miniature rolling pin and features step-by-step photographs.  Lauren and I have been working together to get this class set up after working out some of the problems with the photos.  It seems we needed to get much closer for everyone to better see the instruction pics, and we think we've got it down pat now.

The photos take a while to load, but we feel it's well worth the wait time.  All of the classes will remain on the website so that anyone who just joined us, or needs to refresh, can review any of the lessons.   If you've got questions, suggestions, comments or ideas, please contact me privately.  This is a busy season for us and I have not had time to read all of the online miniature's groups digests.  There's a lot we can learn from each other.

Gerda van Dijk


Previous 10 | Next 10


Page 975 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)