Cleaning Oil-Based Stain from Brushes: I have used oil-based stains for the past 20 years. I don't own a can of water to put them in, as I clean and reuse them. The things I do throw away, I allow to dry out first, before putting them in the garbage. If you want to dispose of your brushes and rags, and don't have a can of water, just lay them out somewhere to dry. Drying oil-based products generates heat. If you have a lot of things soaked in petroleum products drying, such as several brushes and a heap of stain-filled rags, the heat can be considerable and spontaneous combustion can occur. The water acts as a heat sink, keeping the heat generated below the ignition level. However, one brush, allowed to dry naturally before permanent disposal, will not constitute a problem. If you want to be extra careful, place it on something fireproof (a couple of bricks, a clay tile, etc.) and make sure it is not near a wall or curtain.

Jeanne


Quick Grab Glue: I use nail polish remover on a Q tip or paper towel over a toothpick to keep the glue under control.

bill


Small Drills: I use quite a few very small drills, in sizes 61-80, which are tough to get back in order and back into the drill index once they are mixed up. The first and most logical way of dealing with them is to only take one drill out at a time and to put it back in the index when done. If only everything were that easy.... When you do have to use more than one in a session (as for example, drilling several test holes to figure out which size you really do need), I find it helpful to poke the drills themselves into a piece of paper, much as you would anchor a needle in a piece of fabric. Then you can write the size of drill on the piece of paper and it's a little easier to keep track of the sizes that you have "in use." And, if you stick the drill into a little Post-It, you can temporarily stick it onto the project that you are working on when you have to go do something else, such as make dinner...

By the way, some useful drill sizes to know: #72 is the same size as a common sewing pin, #76 is the size to use for the Reallife line of hinges and pulls, and #70 is the size for the larger Houseworks hardware line.

Pam Boorum


Tools: Micro mart makes a tiny portable scroll type saw that is fabulous for cutting windows etc. You just drill a tiny hole to insert the blade and it cuts GREAT!

Sue Thwaite


Tools - Hole Cutting: Saw a Dremel accessory the other day that converts it into a smaller Zip saw. It had a clamp on base and a side cutting bit. Can't remember exactly but it was under $25.00. Clamp on a steel carpenters square for a guide. Plunge into the center of the window and cut out to both ends of the desired dimension. Then move the square, reclamp and repeat for the other two sides. If you do much of it, make a little block equal to the distance from the edge of the base to the edge of the bit. This will let you set up without measuring as long as you don't throw the block out as trash or use it in the wrong direction.

Don Dickens


Glues - I have switched from Zap-A-Gap to Quick Tite liquid and/or gel. No more stuck fingers or hands...has a special dispenser, no clogged ends. Also does not have fumes as bad as ZAP. GREAT STUFF! My favorite white glue is WELDBOND. Not as thick as Tacky, but thicker than ELMERS. Dries clear and will glue PEWTER, metals, Styrofoam, glass, etc.

Sue Ann Thwaite


If you use a glue syringe or glue bottle with a very small hole, to keep it clear of glue, use a plastic price tag thingy, (the long thin bit,) in the hole, when you are not using it. It doesn't rust, (like a pin), and it's easy to pull out.

Alison Fleming


Moveable miniatures glue: Any store that deals with Dee's should be able to get it for you. I have an extra bottle that I can sell to someone if they are interested. Just email me.

Susan Karatjas


Quick Glue, Zap, Hot Stuff Etc. - Re: Quick glues and the problems, there are two ways to prevent or at least reduce the mess.

1. Always use hand lotion such as Jergens etc. before handling the glue.

2. Buy a bottle of glue remover and keep it handy.

After 54 years of building Sailplanes you learn what works, especially if you have two fingers stuck together for a couple of hours.

Marshall R. Searcy


Moveable glue: I have some bottles in stock. You can email me privately if you'd like one. I love the stuff.

Carol from MA


Previous 10 | Next 10


Page 976 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)