Safety Tip: Those spongy things that fit on pens or pencils also fit on x-acto knives and keep them from rolling off the work bench and ending up point down in your leg!

Patricia A. LeBeau


Roo Glue: Roo Glue is available from Rainbow Design or Sandy's Lace and Trims. Ask your favorite miniature shop to order it or contact RB or Sandy’s. Both MiniRoo for wood and Roo for Metal and Plastic are available.

Dean Jenson


The Jarmac table sander is my FAVORITE tool. I use it for shaping and filing and everything. Every time I have a visitor to my studio they end up ordering one from me. Just use the self-adhesive sanding pads and they peel off when you are ready.

Sue Thwaite


For the new people, I have found that when working with glues if I keep a bottle of Goo Gone handy with Q-Tips and paper towels it save a lot of clean up time when you are done. Messy fingers leave messy work.

Sandra Smith


Precauions: I HOPE YOU aren't cutting off with a saw blade in the Dremel. That is an absolute NO NO! The Dremel should be anchored down andthe blade should be cutting through a table. There have really been some very serious injuries using a saw blade in a Dremel. Please do not use saw blades in a Dremel unless you absolutely know what you are doing. I don't. Use cut off fiber discs to cut off but then use goggles as the discs can explode.

Bill Hudson


Ribbon shredders: Just about any craft store or card store will probably carry ribbon shredders - with the ribbon, naturally.  They have a little row of 'teeth' - look like little pins - spaced evenly apart to 'cut' the ribbon in nice neat strips.  A party supply store may have them too.

Laura


Rulers: The thin flexible ruler with the little slots to make pencil marks through is probably an Incra. They have a number of configurations available, and with a sharp pencil, you can be very precise. I have seen them in woodworker's stores and catalogues and I believe Post Tool carries some of them.

Jeanne


I usually use a little super glue (ZAP-A-GAP is my preferred brand) to glue those brass hinges in place, then I just push the little nails into the holes (if present). The glue holds the hinge nicely in place and will help keep you from pulling all your hair out while you install the nails (I say this from experience - LOL).

Laura


The tip on using super glue to place hinges before nailing was good, but be sure to put only the smallest amount possible on the edges farthest from the actual hinge. I have gotten glue inside of the swivel and that is the end of THAT hinge, especially the little mini ones!

Bonnie Gibson


Basic tools: Usually, a 'basic' miniaturist's tool box will have the following items:

small scissors (for paper and/or fabric)
a 6-12" metal ruler (metal is my personal choice; better accuracy than the wooden ones)
pencil
notepad
sharp-pointed tweezers (curved or straight ends, whichever works best for you)
an X-Acto (brand; also called 'craft knives') knife with #11 blades (this being the 'standard' size for most minis work)
some toothpicks (good for all sorts of gluing jobs, etc.)
some misc. grades of sandpaper
some craft glue (I like Bond brand, Instant Gripp, but a lot of us use Aleene's Tacky - in the gold bottle)
maybe some small clothespins (great clamps)
some sewing needles (along with some white thread, usually)
a small pair of pliers
a small wire cutter (or a decent nail clipper)
maybe even a small hammer
a couple of decent, fine-line paintbrushes
a 'junk' brush for spreading glue
I try to keep a zip-lock bag with Baby Wipes around, to clean off my fingers, get glue/paint off tweezers, and stuff like that.

Laura


Previous 10 | Next 10


Page 982 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)