Paintbrushes: Since it is so hard to find paint brushes small enough for some of our work, I buy the smallest I can find then cut off all but a hair or two.

Pat


Styrofoam glue: I saw a special glue just for styrofoam at Pearl Art and Craft.  I tried to find their web site but couldn't access it.  Maybe you have a store near you, but there IS a glue that is just for styrofoam.

Judy


Cutting moldings: When you place the molding in the miter box, place the part of the molding that goes against the floor or ceiling against the back (upright) part of the miter box.  It also depends of whether you are cutting an inside corner or an outside one.  One is cut with the wood to the left of the slot, the other with the wood to the right of it.  I have my miter box marked with masking tape to remind me which way to place the wood but don't have the box with me so can't tell you which is which.  Experiment with plain stripwood to determine the correct way to save wasting any more molding.

Rose


Kemper Double-Ball Stylus: I discovered a wonderful modification through Maritta Rucker (Nimble Fingers) when I bought a couple of her kits a few years ago. With a Dremel (or similar rotary tool) and a grinding attachment, gently grind down one end to a point.  USE PROTECTIVE EYEWEAR, Please!   Lightly smooth that point just a bit with a nail file, emery board, whatever.   You'll have a great 'veining' tool for flower leaves, and still have one end for shaping flower petals, too.  Maritta 'pointed' the smaller ball-end in her kits.

Laura


Bandsaw: Have fun with your bandsaw.  I have had one for 20 years and am on my second motor.  I use mine for rough cutting woodcarving blanks and fast cutoffs.  You can do lots of things on it including rough ripping blocks of wood into mini thicknesses.  Be sure your guide is adjusted as low as possible towards your work to keep the blade from "traveling" and cutting crooked.

When cutting an angle, you piece stays flat on the table even if the table is tilted.   You just can't move the blade on a bandsaw so they fixed it to move the table instead. I didn't really understand what you were trying to do with your twigs, write me privately and maybe we can figure it out together.  And by the way, it IS a good idea to keep your fingers away from the blade...LOL.

Bonnie


Cutting Circles: You can get a hole saw to cut your circles. This resembles nothing as much as a nest of cookie cutters! Maybe six or seven round, toothed 'cups' in various diameters, which attach to an electric drill. Perfect for making birdhouses, openings for Housework's attic windows, etc. The one I have belonged to my dad, but you can ask at Home Depot or such. "Adjusting the guide"...Let me see if we can do this with drawing pictures! The blade on my band saw (a Skillcraft) comes down through a sort of box that has a sticker on it "Warning: Keep fingers Away From Blade". This 'box' can be moved up and down by loosening and tightening a knob on the back of the saw; if I want to cut a 1/2 inch board, I can raise the guide, and if I am working on thin stuff, I can drop it to within a quarter inch of the table.  Check the instruction book, as your saw is probably set up differently, but the idea is the less space you have, the less play or wobble there will be in the blade.

Dani


Digital Images: An excellent course of action where digital cameras are concerned is to get the biggest, baddest, most expensive piece of equipment you can possibly afford. Most of the decent cameras are relatively easy to use. If you want the convenience of digital photos, there is a learning curve that is important. The more you understand about digital images the better quality you will be able to produce.

I find that the Olympus line of cameras is quite good (I used to research and purchase all such equipment for the IT department I worked in), and they have several models that are well priced for what they can do.

The key to getting a good quality image is to use an appropriately high resolution. I know in the camera I have (Olympus 300d) I could choose to take and store 150 medium quality images or 40 high quality images. Superficially, the difference was that the medium quality image was 600 x 400 pixels and the high quality was 1024 x 760 (one was smaller than the other). It was hard to see the quality difference at first. That comes when you try to resize the image. Since the high quality file is storing more information about the image, you can manipulate the image with less loss of quality.

When taking photos to post on a web site, you can archive those large files and use a copy to make the image to post. There are lots of tricks to reduce file size (for faster loading time and stuff) but still maintain a standard of quality. If you want a good picture of a mini, take it at high resolution then open the file in an image editor and crop and resize to really feature the item. You may find that some gentle manipulation of the brightness and contrast can improve an image as well. You can also improve (to a limited extent)focus and color values.

Pardon the long winded post, but it is my absolute pet peeve to shop on a site with bad images of the goods. Nothing makes me close the browser faster.

Jeannette in San Jose


Precautions: I agree, you should NEVER, NEVER use a steel saw blade in a Dremel for a freehand cut. There are trim and rip saws out there that use Dremel tools as a power source, and you can be very accurate and get a square cut with them. They involve putting the Dremel into rather elaborate jig and clamping it down to the table. Then the tool stays still while the wood is controlled with your hands and moves past the blade. Bob Scott makes them, I believe, and I have seen him at the Seattle Show. Anker Rasmussen used to make them, but he has retired. Dean Jensen of Rainbow Designs took over a number of the things Anker used to make, but I don't know if he continued with the trim and rip saws. His address is RainbowDJ@AOL.com. I don't know Bob Scott's e-mail address but check with Helen at MindStorm helen@mindstorm-inc.com

If you want to use the Dremel freehand, it is great for engraving, sanding, grinding and other applications that do not involve a steel blade. However, remember that the tool can move up to 30,000 RPM, and when it gets too close to a corner can catch and either hurt you, or damage your piece. Practice with scrap - it's the only way to learn how.

Jeanne


Eyescrews: Someone asked about small eyescrews.   MicroMart has them in their catalog.

Another person talked about trying to crochet and having the DMC floss coil. This solution works for doing cross stitching - which is to thread your needle with floss and before making the "waste knot",  run the needle and floss through a sheet of laundry anti static material.  It works like a charm and gives off a nice scent.   Perhaps it would work with crocheting also.

Jeanette


Cutting Plexiglass: Use a table saw to cut plexiglass but apply a cutting and drilling fluid to the blade first. Caution: unplug the saw before applying the fluid. The fluid is sold by tool supply shops.

June


Previous 10 | Next 10


Page 983 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)