Stump houses: Our club here in Hawaii has been doing stump houses for several years. We use Clorox bottles. Stand it up, cut a hole in the side and using your favorite (we have several) paper mache goop, dip and paper towels in, and place on the bottle in folds and wrinkles to simulate bark. You can add brown paint to the goop (work on newspapers) and then paint on highlights with darker brown and black acrylic paint. We all add our own chimneys, sometimes a floor in the middle, stairs on the inside or out, a window or two if you like, vines and flowers and your own little critters or fairies etc. One of our ladies used the plaster impregnated cloth used for casts for her bark, and one even used real bark. Just a few ideas, Hope someone can make use of them. Norieta in Hawaii |
Dollhouse Preparation: I too have a Duracraft and was advised to put a primer coat on every piece even before construction. I did that with a name brand white flat paint and then some sanding on the inside. It has worked beautifully. The only thing you need to watch for is glue that may have dripped and dried before you saw it. This happened in a small area on my house and it took some elbow grease to sand it off. I will be more careful next time. Barb in PA |
Grape Vine Wreaths: For making grape vine wreaths, all you need is cloth covered wire, sold in floral departments at most craft-related stores. If you can't find brown, get the green, wind it up in a circle the size you want, giving a pinch and a squeeze here and there so the wire isn't perfectly straight and bumpless, and then paint it brown. Add your decor and it's done. Marjorie in CA |
Simple SW House: A simple SW house (no shingles) in 1/4" scale {1"=48"}. Sorry I couldn't find my metric ruler to footnote these measurements. Their walls were 1 to 2 feet thick, so I use 1/4" plywood. CUT... 2 long walls {for a front & a back} 6 1/2"wide & 4" high 2 short walls {for ends} 3"wide & 4" high 1 floor 3" by 4" 1 roof 2 7/8" by 3 7/8" 1 inside wall 3" wide & 3 1/4" high 4 Vigas = 1/4"dowel cut 4" long {timbers that hold up the roof} Strip of wood 1/16" by 1/8" {to trim over door & windows} The floor of this fits INSIDE of the walls. The inside wall sits ON the floor. Other builders have set all of the walls ON a base & the rest of the base becomes patio & etc. DECIDE WHERE YOU WANT THE WINDOWS & DOOR. CUT openings into the walls for them. Measure a piece of Strip wood {see parts list above} 1/2" longer than the width of each Window & Door opening. LAY the Strip above the Door opening. The bottom of the strip should touch the top of the opening for the Door. DRAW around this strip. The Strip will be glued in place AFTER painting the Wall. DO NOT PAINT WHERE THE STRIP WILL GO. Repeat this for each window opening. These Strips represent Heavy Timbers and were very dark in color. You can put Strips on the inside too. CUT an ARCH in the back wall for access. Measure 3/4" from the LEFT side of the Back Wall and draw a line from the bottom of that wall to the top. Measure 3/4" from the RIGHT side of that wall and draw another vertical line. Measure UP from the BOTTOM of that wall 3'' and draw a line from the left to the right of that wall. This will create an opening 5" wide & 3" high. At the UPPER corners I like to use a coin to create rounded corners, thus giving it the look of a wide arch. CUT OUT this arch. The Inner Wall will have a doorway cut into it. Measure from the RIGHT side 1" and draw a vertical line. Then measure UP from the BOTTOM 2 3/4" and draw a horizontal line to meet the first line. At the UPPER left corner again use a coin to create a rounded corner. CUT OUT this doorway BEFORE doing the next step. One room is larger than the other. My larger room will be on the left {as seen from the Back of the house}. BEGIN at the left side of the floor and measure 3 1/4" toward the right and draw a pencil line from the front to the back of the floor. Stand the Inner Wall on the right side of this line & touching the line. Be sure the long side of the Inner Wall lines up with the front of the floor. Now draw around the rest of the Inner Wall. This wall sets perpendicular to the front wall. This part of the floor will NOT have tile (or other floor covering on it). MAKE A PATTERN of the floor area that WILL have tile (or ??) on it. This will make it easier to install a floor covering later. Lay the Back Wall ON the Front Wall. Make sure the edges are EVEN all around & CLAMP the two walls together. The holes we will drill for the Vigas MUST BE in the same place in each wall. On the wall...measure down from the TOP 5/8" and in from the LEFT side 5/8"...PUT A DOT HERE. Measure to the RIGHT 1 3/4" & put the Second Dot. To the RIGHT 1 3/4" & put the Third Dot. The Fourth Dot is 1 3/4" from the Third Dot. AND 5/8" from the RIGHT side of the wall. ALL of these dots MUST be 5/8" from the TOP of the Wall. DRILL a 1/4" hole CENTERED on each Dot and drilled through BOTH Walls. You may have to sand the Dowels a little to fit these holes. They should fit easy, but not sloppy. Glue the Walls AROUND the Floor, using the Vigas in their holes to keep everything lined up. When all is DRY, remove the Vigas and PAINT the walls inside & out. MIX some VERY FINE Sand into the paint to create stucco. Clean out any paint that gets into the Viga's holes. Don't get the paint too thick above the Viga's holes. The roof goes here and sits in the Vigas. Paint the top of the Roof BLACK to be the tar or pitch that normally goes on the Roof. The bottom of the Roof piece is the Ceiling of the house. Decide where the Fireplace will be. Attach the Chimney FIRMLY to the Black side of the Roof. It becomes the "handle" to remove the Roof piece. I like to remove the roof when I show someone my house as it lets more light in. I hang things from the Vigas, not from the ceiling. Ann Bramlet |
Spiral Stairs: A hint I got some time ago in SSD is to use an oriental fan for the stair treads - the carved ones that look like wrought iron. I have seen these in plastic but the only oriental shop in my town had them in wood - very thin & laser cut. I have started mine, but it may be awhile before I work it all out. I plan to seal the thin wood with gesso on both sides (for strength) and then to paint them black. I will string them onto a dowel with fancy beads between to space them properly. I will then make a banister using spindles and I will top it off with a rail using either the covering from copper wire or the fine bendable wicker used to make baskets Jacqui in Hilo |
House Plans: This is not quite what you asked for (Norman castle Americanized etc.), but I thought I'd mention the Dover reprint of American Victorian Cottage Homes (full-sized ones, not dollhouses). They are by no means what we'd think of as cottages--some are about 6 stories high, or townhouses--but they are often incredibly complicated, with gables everywhere, and towers (but not round ones). There are perspective drawings and elevations and floor plans. Might give you a few ideas. Originally published in 1878 by Palliser, Palliser & Co. Frances Armstrong |
Contemporary minis: Hi to all those interested in contemporary miniatures. Just ran across an interesting art site that offers an architects idea of a dollhouse with a very different view - it is fun to look at and they also offer interesting accessories. The URL is as follows: Ann Hendricks |
Dumbwaiter - My motor did not need to reverse. It was mounted in the attic of the building. Think of a rectangle for the attic floor. Mount the motor in the very middle of the attic floor front to back. Mount an arm on the motor, say a piece of aluminum that is ½" wide by 4" long that swings around the motor. Drill a hole in the far end of the arm, tie cord to arm and top of dumbwaiter. As the motor and arm go around the cord gets pulled to and fro the dumbwaiter and it goes up and down. |
DUTCH DOORS: Standard doors may be cut for Dutch doors IF they are not mid panel at the height you plan to cut (Usually about 33 to 40 scale inches. Cut an extra 1/16" out and install a small "shelf" on the lower section. If cutting a single door will not work, look at using sections from two doors. Completely rehinge both sections Except in the earliest architectural periods, Dutch doors usually look most appropriate if the top half has a window. I have never seen a "tall" door of this type. You are correct that the knob and locks usually belong to the bottom half. Don't forget to suggest a vertical sliding "bolt" to latch the top half to the bottom when you want them working together. Dutch doors are very common where cross ventilation is desirable while maintaining some degree of closure to deny access to chickens, dogs, and vagabond beggars. Kitchens, workshops, carriage houses, and tiny shops that sell through the doorway" are familiar settings for these charming portals. Mel Koplin |
Grape Vine Wreaths: When I make grape vine wreaths, I use the thinnest stems from my bridal veil spiroria (my spell checker can't even spell that). I cut them while they are very fresh and pliable and then I soak them in hot water just before I use them. They will bend very easily then. I tie them with tiny brown thread and put thedecorations over the thread. They are realistic and easy to do. They last forever. (Well, maybe not that long - after all, I haven't lasted forever yet). Carol Atchley |
| Previous 10 | Next 10 Page 990 of 1032. Total links in database: 10312. |
|
Browse the database (all entries) |