Wattle and Daub: Wattle is the intertwined sticks that are placed in a wall between the posts (kind of like lath for plastering).  Daub is the mixture of clay, sand and dung that is smeared (daubed) into and over the wattle to make the wall.

Tom Berkner


Wattle & Daub:  There's a great website that shows a cottage with wattle and daub walls under construction --

Popular Cottage contstruction - thatch - wattle and daub

Anita Myers, Arnold, MD


Drawing Dollhouse Plans: You don't have to limit yourself to 3 stories if you're wanting LOTS of rooms... Charleston's homes on the Battery have 5 stories (best I remember it was 4 stories and a half above-ground basement) so you could go even higher if you want LOTS of rooms!! Makes sense to me. That way you get lots of rooms and still not take up much footage. These houses were also 1 and 2 rooms deep...very easy to pattern a dollhouse after. They are what we would call "sideways" on their lots, meaning the long "front" of the house is usually to the left (South) inside a fenced courtyard and you are looking at the short "end" from the street. (The reason for this was to catch the coolest breezes. By the houses being only 1 or 2 rooms deep, this helped to cool all the rooms.) Sometimes a regular house door was used to get inside the courtyard to go to the house to knock. I found these houses fascinating. So if you want even more rooms, go ahead and add more stories! And have fun!!

Rita Pierce


Mini Windup Alarm:  Make your own mini "big Ben" brass alarm clock.

Materials:  3/8" brass tubing from model supply -OR- 3/8" brass compression sleeve from the plumbing section of you local hardware store.  2 Brass beads about 1/8" diameter,  1/32" solid brass rod, 1/16"  solid brass rod -OR-  1/16" brass beads,  brass foil or thin shim stock,  piece of card stock,  photocopy of a clock face,  super glue, clear lacquer spray paint, a bit of thin clear acrylic.

Tooling: small bench vice,  small center punch and hammer, razor saw  -OR- tubing cutter, 1/32" & Maybe) 1/16" drill bits with pin vice or moto-drill, mini hack saw, light metal file, wire cutter, scissors.

Miscellaneous: toothpicks, emery boards, working place mat AND SAFETY GOGGLES

You can make an alarm clock body cutting a ring from the length of tubing. The compression sleeve also makes an interesting body for the clock though it has a little more shape than was/is authentic for such pieces.      Mark carefully for two large bead "bells" with a clapper between them on the top of the clock. Each of these marks should be indented with the center punch and then drilled through with the 1/32" bit. Hold your clock body firmly in the vice while center punching and drilling.

Flip the clock body upside down. Mark, punch, and drill four holes for EITHER. 1/32" rod to secure the 1/8" beads as feet  -OR- 1/16" round rod feet.  If necessary, enlarge the holes in all beads to accept the 1/32" rod.

Use a piece of 1/32 rod to help hold the larger beads as they are filed flat on one face (with hole in middle of flat face. These may then be super glued onto a short piece of 1/32 rod and that wire glue into the side, top holes of the clock. Glue another piece of 1/32 rod into the middle hole as the clapper.

NOTE: A lot of this assembly work you will want to prepare for and prefabricate but not assemble until after polishing all parts nice and shiny with household brass polish.

Insert rods into "feet holes" on bottom of clock body. Bend slightly as needed to extend straight up inside of clock body to top. These will be used to position and mount your clock face and back cover. Secure with super glue at top and bottom.

If you are going to use beads for feet (with 1/32" rod) slip beads onto rod with a tiny bit of super glue to hold.

Cut bits of card stock to fit neatly inside clock body both front and rear. Install clock face on one. Position front one first, assure rightside-up alignment and apply super glue from back.

Cut foil or shim stock for back body of clock and secure to second piece of card stock. Assemble.

Allow super glue to fully cure over night. Clip, emery board, file excess wire from feet until clock sits erect & stable.

Find scraps of smaller brass wire and smack one end with a hammer to flatten it out. Do this to form "handles" on two windup keys. Shape with a file. Use a needle to punch holes in back of clock for the two "keys" plus two unflattened bits as time and alarm "set" screws.

Touch up polish of clock and coat with fine layer of clear lacquer. Lastly, cut a front "glass" out of acrylic and fit over the face. Do not put hands on the clock. Miniatures are timeless. DO use safety goggles whenever cutting, drilling, clipping, or spraying. There is so much yet to see.

Mel in Vegas


Wine Glasses: I have some glass wine glasses on my website which I think are nicely done and "reasonable." Of course, the definition of reasonable is subjective. They're at http://www.spminiatures.com/glasscrdecan.htm

Carol


Wattle & Daub: We were using wattle and daub here in the UK, long before the Romans brought over cement.  As well as mud, we used dung and hay, so the buildings must have been really smelly.

Hazel in Aberdeenshire, Scotland


Mel's clock: I would like to add one more idea to Mel's clock.  If you find the vise wants to crush your copper tubing, or other small, round, hollow items...insert a dowel into the tube and cut or drill the tube and dowel together.  I've even used a pencil or twig, because I didn't have the proper size of dowel. It is cheaper to cut off a little dowel, than replace crushed tubing.

Ann in AZ


Slanted Wall: I went on a Christmas candlelight tour of homes this last weekend. I toured an 1800's home where there was a bathroom on the second story that had a slanted wall. The owners had taken a large piece of lace and attached it at the top of the wall and the bottom of the slant. When they attached it they had gathered the lace. It really looked wonderful. It looked like a curtain that you would put on a door that has a window in it and the curtain would be on spring rods at the top and bottom.

Tracey


Wattle and Daub: Wattle and daub is an ancient technique used for constructing houses, especially in areas where there was no suitable stone. It was used as an  infill in timber framed houses. first a 'wattle' made of woven hazel or  willow was put up, then plastered over with daub. Daub was often made with  dung. It was painted with limewash, distemper or something similar.  It's found in houses from the early middle ages (1066), and nobody really  knows how long it had been in use before that, although I suppose a good  archaeologist could give you an estimate.

Lynne Connolly


Menorahs: I have a few sources for you.  The first is "In the Beginning" which has a very nice selection of Judaica, including several menorahs.  Go to their web site - http://showcase.netins.net/web/novacon/dollhouse/itbindex.htm - and request their catalog (it's free).  They have only one seven light menorah, and unfortunately it is not pictured in the catalog.  However, the price is only a few dollars, so you could just take a chance order it.  If you are looking for a sterling menorah, Don Henry makes a beautiful one, which you can see on and purchase from the SP Miniatures web site: http://www.spminiatures.com/index2.html.  It has nine lights. HBS http://www.miniatures.com  has a couple of menorahs in their catalog, but they are also nine lights.  The thing is, they are so inexpensive that you could easily cut off the outer branches, and file the cut spots smooth.

Jonathan in Israel


Previous 10 | Next 10


Page 991 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)