TXp>Crate Labels: There is a web site that has a lot of antique crate labels you could print off and use. Lots of stuff in a zillion different categories. You'll probably get inspired to do a half dozen more projects! http://www.sover.net/~oldlabel/unframed.html

Dani in Bradshaw


Close up Photography: I took a simple; inexpensive magnifying glass and held it in front of the lens of the digital camera; perhaps a few inches between the lens and the magnifying glass. I then moved the camera and the magnifying lens (while viewing the object & image) until the image on the camera view screen appeared in focus. I then moved the magnifying lens closer and further from the camera lens until I enlarged the object to my satisfaction. It will tke some moving of the camera and the magnifying lens and the distance from the subject until you are satisfied. I took the photo and lo & behold It functioned as imagined. Visit my site and compare the 2 photos of the wind chimes. The flash can be seen in the close-up shot as a bright smudge to the right. The Chimes were over exposed from the flash but the concept works!!!! It works.& cost next to nothing so try it out.

Dr. Bob


Digital Cameras: I have an AGFA CL30, in the $300 range, not the cheapest, not the most expensive. I can't tell you that there is not a better one out there for the same money, but the following is my experience with what I have. I had to purchase 2 additional items, a set of macro lenses-very necessary for sharp close-ups, and an AC cord for the camera. Relying on batteries for use of the camera results in going through a LOT of batteries. Because 99% of my use of it is at home, using the cord is fine (Cost of lenses and cord, another $100). There is a learning curve for getting really good shots, but the beauty of a digital camera is that you can just keep shooting until you get it right. I have taken thousands of shots, and deleted most of them. But I also have a lot of great pictures! I was using a regular (good) camera before the digital, and my pictures of the minis are much better now. Not to mention no longer having to go in and pay to develop a bunch of bad pictures. Some questions to ask when evaluating cameras: Does it come with a macro lens? If not can one be purchased? How long do the batteries last? Does a power cord come with it?

Cyndi


Digital Cameras: I have recently obtained a used digital camera, not of the highest resolution. But if you do not like the photo take another. Regarding close ups. The camera a have does not have any lenses to attach as my film camera has. What I did was I put a $5.00 magnifying glass between the camera lens and the subject and maneuvered the lens and camera until I saw what appeared to be what I wanted, then took the photograph.

Bob


Sizing digital pictures: If your pictures are too large to upload quickly:

1) Some cameras do have a setting for low resolution pictures. Check your owners manual.

2) Most pictures can be "compressed" with picture editing software. There are many different programs to choose from including some free ones that can be downloaded from the Internet. When you compress a picture you lose a tiny bit of quality- but not really that noticeable.

Bonnie in Tucson


Plates: Recently there have been several people asking about plates so I thought I would contribute as follows, although this will be old news for many of you: I make plates and bowls from a two part clay that we can get in South Africa. It is similar to Prattley's putty that is used for fixing car parts. However, in England I think Milliput would be the closest. Otherwise air drying clay such as Das, which is available in white, would do the trick and maybe now Paper clay. These instructions are for the two-part clay:

I take a pea-sized piece of each clay and mix the two together thoroughly. I then roll it between 2 pieces of wax wrap, on a tile, using a glass as a rolling pin. This gets the clay smooth and thin. I take my mold, which is usually a lid of some sorts, and put a THIN layer of Vaseline as a release agent. I lay my clay over it and use my craft knife to cut off the excess. I smooth edges with a "wet" finger. (Sorry, nothing else works!) I leave these to dry overnight and then pop them off their molds. I wash them with HOT soapy water to remove any Vaseline residue. A light sanding smoothes off any rough edges and imperfections.

I make colour photocopies of plates reduced to the right size. They must be full face on, bright and clear. Of course, if you want a dinner service, and not just plates to hang on the wall, then you must make bowl-size copies and side-plate-sized copies, as well. I paint these with decoupage transfer medium, leave to dry and then cut them out VERY accurately. I then soak them overnight or longer (they take no harm left for weeks). Meanwhile, I paint the back of the plates with decoupage deco-varnish to give the back a finished look. I rub the paper off the back of the photocopied plates leaving a thin transfer. I slide this onto the wet plates with deco varnish, position it, smooth out any bubbles with a wet brush and then leave them to dry. 3 coats of deco varnish, with drying time between, finish them off with a shiny finish.

Barbara B, South Africa


Snowshoes: the last time I was at Fred's Dollhouses and Miniatures store in Pittsford, Vermont (they advertise in every Dollhouse Miniatures magazine phone number: 802-483-6362), I saw exquisite snowshoes. I think they may have been made by a local crafter. They were expensive, but they were perfect. On the other end of the scale, my sister got very cheap snowshoes at Michael's.

Melissa


Plates: I was looking at punches and found a great site.

http://scrapramento.com/Punches/FTPreview/PunchShapeSets.html

This punch set is a set of round punches. Hard to see but I think various sizes up to about an inch. Since we have been "talking china," I thought how about using cardstock and punching out circles. It is hard to believe but some items that are made from cardstock can be very "china like." Use a 1" circle with a 3/4" one on the bottom, flare the edge, using a bone folder tool, or other tool. Glue together and decoupage with transfers made from Transfer medium. Eileen's "Transfer It" is one product. You can find it in most of the craft stores. (This idea was on the list just recently. Want to give credit but can't remember who. Thanks to you most kind person.

This might make some nice plates. Instead of Decoupage, you might try water-based polyurethane. This has worked well for me on other things. You could also print out printable plates onto cardstock from the web and punch them out with the punch, since the major thing is getting them nice and round and exactly the same. Karen from Dubai just put this site up on the last SS digest MSATMiniatureCutOuts@yahoogroups.com

Barbara D


Salt box: I'm not an expert, but what I do know is that the early saltbox had these traits: a room with a brick cooking wall, hearth, bread oven and such. Also in the living room a fireplace, formal, with chair rail if the family could afford it, and almost always, exposed roof beams to hold up the other floor.

The library has a treasure trove of this historic structure. My library has in its art dept.

Susan


In the course of designing a couple of RL houses in the past few years, I've found that the easiest off-the-shelf architectural design software is 3-D Home Architect by Broderbund.  You can draw the basic outline of the floorplan pretty easily, add windows and doors, make your open walls invisible, add second or even 3rd story, put on a basic roof, then view it all in 3d, move through it too if you like. There are some basic furnishings you can put in and move about, and basic wall/floor colors.

If you have a complicated roof, I've found it simpler just to make a print-out of the 3-D elevation and sketch in the roof myself, as the roof design procedure, being meant for RL building, is fairly complex.  (Also, you will be unlikely to find any sample plans in any architectural software that can be used for a dollhouse; they are all made as samples of RL houses and way too complicated to edit--easier just to start drawing your dollhouse from scratch, IMO.)

There are other inexpensive non-pro CAD-like programs, but the others I've tried, Sierra Home Design and AutoDesk Home Designer, do not build the stories on top of one another, so you don't get a full 3-D view of the whole thing.

JJ


Previous 10 | Next 10


Page 996 of 1032.

Total links in database: 10312.



Search for:


Browse the database (all entries)